31
Lock
WiFi
S\N
Primary Filtration Menu
During the primary ltration cycle, the circulation pump and
CLEARRAY are activated. The spa is programmed with a defau-
lt setting starting at 12:00 AM and lasting for 8 hours, but this
can be changed. This cycle allows the circulation pump to run
for a preset amount of time per day, in addition to the normal
operation.
Note: Any time the circulation pump runs outside of a program
cycle, e.g. for heating, that run time will be deducted from the
next primary lter cycle. For example, the primary lter cycle is
set to 8 hours every 24 hours but the circulation pump comes
on for 2 hours to heat the water after the cycle has nished. The
next primary lter cycle will only be for 6 hours not 8 hours.
Programming the Primary Filtration Cycle
To change the programmed Primary Filtration Cycle:
1. Press ( ) until you get to the “PF” Menu. The display will
scroll “PRIMARY FILTER.” After the second scroll, if no action is
taken, the system will revert back to the Main Menu.
2. Press or to display the current start time and prepare
the system for changes.
3. Press or to adjust the start time, in 1-hour increments.
To switch from “AM” to “PM” you must round a 12-hour period.
4. Press (
) to conrm and save the start time.
5. Press or to adjust the duration of cycle, in 1-hour in-
crements.
6. Press (
) to conrm and save the duration time. The system
will return to the “PRIMARY FILTER” Menu.
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current
settings will remain active.
In extreme bitter cold weather, where freezing can
occur, we recommend you program the primary l-
tration cycle to run 24 hours. Refer to the “Winteri-
zing” section.
Secondary Filtration Menu
The jets pump 1 activates during the secondary ltration to
provide additional skimming. The spa is programmed with a de-
fault setting of Holiday Mode, but can be programmed to other
modes. There are 3 dierent modes, Holiday, Light and Heavy
Mode.
Note: During the secondary ltration the jets pump 1, circula-
tion pump and CLEARRAY are activated.
• Holiday Mode disables the Secondary Filtration.
• Light Mode will activate two 10-minute cycles every other
day; one at 8:00 AM and the other at 8:00 PM.
• Heavy Mode will activate two 10-minute cycles every day;
one at 8:00 AM and the other at 8:00 PM.
Programming the Secondary Filtration Cycle
To change the programmed Secondary Filtration Cycle:
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current
settings will remain active.
1. Press (
) until you get to the “SF” Menu. The display will
scroll “SECONDARY FILTER.” After the second scroll, if no action
is taken, the system will revert back to the Main Menu.
2. Press or to enter the Secondary Filtration program-
ming. Continually press to scroll through the following modes:
• Holiday Mode: The screen will display “HOL” and scroll “HO-
LIDAY MODE.”
• Light Mode: The screen will display “LT” and scroll “LIGHT
MODE.”
• Heavy Mode: The screen will display “HVY” and scroll “HEAVY
MODE.”
3. Once a selection is made, press () to conrm and activate the
setting. The system will return to the “SECONDARY FILTER” Menu.
Programming the Heating Mode
Your Jacuzzi spa is equipped with 3 modes of heating. An auto-
matic mode called “AUTO,” where the spa’s temperature is main-
tained at all times. An energy saving heating cycle called “ECO.”
A mode that will only activate the heater during the daytime
called “DAY” mode.
Note: The heater will activate when the temperature drops 2°
from the set temperature.
• Economy Mode is an energy savings program. The spa is al-
lowed to heat between 5:00 PM and 7:00 AM every day. The
hours are not programmable.
• Day Mode allows the spa to heat during the day, between
7:00 AM to 5:00 PM. The hours are not programmable.
• Auto Mode allows the heater to heat, at all times, in order to
maintain the preset temperature.
Programming the Heating Mode
To change the programmed heating mode:
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current
settings will remain active.
1. Press ( ) until you get to the “HEAT” Menu. The display will
scroll “HEATER MODE.” After the second scroll, if no action is ta-
ken, the system will revert back to the Main Menu.
2. Press or to prepare the system for changes. Continual-
ly press to scroll through the following modes:
• Economy Mode: The screen will display “ECO” and scroll
“ECONOMY MODE.”
• Day Mode: The screen will display “DAY” and scroll “DAY
MODE.”
• Auto Mode: The screen will display “AUTO” and scroll “AUTO
MODE.”
3. Once a selection is made, press (
) to conrm and activa-
te the setting. The system will return to the “HEATER MODE”
Menu.
To Next Page
Loading...
Need help?
General
