Jacuzzi J-300 Series Installation Manual And Use & Maintenance

32
 Programming the Change Filter Timer
A programmable lter timer can be set to remind you when to
clean or replace the lters.
• The default setting is for 180 days.
• The timer range is from 0 to 180 days, in increments of 10
days.
Programming or resetting the timer.
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current
settings will remain active.
1. Press ( ) until you get to the “FC” Menu. The display will
scroll “FILTER CHANGE.” After the second scroll, if no action is
taken, the system will revert back to the Main Menu.
2. Press or to prepare the system for changes. Continually
press to adjust the length of time for the timer.
3. Once you select the number of days, press (

) to conrm this
selection. The system will return to the “FILTER CHANGE” Menu.
4. Once the timer expires the display will alternate between the
water temperature and “CHANGE FILTER”.
 Programming the CLEARRAY Timer
A programmable change bulb timer can be set to remind you
when to when it is time to replace the UV bulb for the CLEARRAY
system.
• The default setting is for 365 days.
• The timer range is from 0 to 365 days, in increments of 10
days.
Programming or resetting the timer.
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current
settings will remain active.
1. Press ( ) until you get to the “UV” Menu. The display will
scroll “CLEARRAY BULB.” After the second scroll, if no action is
taken, the system will revert back to the Main Menu.
2. Press or to prepare the system for changes. Continual-
ly press to adjust the length of time for the timer.
3. Once you select the number of days, press (

) to conrm
this selection. The system will return to the “CLEARRAY BULB”
Menu.
4. Once the timer expires the display will alternate between the
water temperature and “CHANGE CLEARRAY BULB”.
 Programming the Water Refresh Timer
A programmable water refresh timer can be set to remind you
when to when it is time to drain and rell your spa.
• The default setting is for 180 days.
• The timer range is from 0 to 180 days, in increments of 30
days.
Programming or resetting the timer.
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current
settings will remain active.
1. Press (
) until you get to the “H2O” Menu. The display will
scroll “WATER REFRESH.” After the second scroll, if no action is
taken, the system will revert back to the Main Menu.
2. Press or to prepare the system for changes. Continual-
ly press to adjust the length of time for the timer.
3. Once you select the number of days, press (

) to conrm
this selection. The system will return to the “WATER REFRESH”
Menu.
4. Once the timer expires the display will alternate between the
water temperature and “CHANGE WATER”.
 Programming the Time
To program the time, follow the steps below:
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current
settings will remain active.
1. Press ( ) until you get to the “TIME” Menu. The display will
scroll “SET TIME.” After the second scroll, if no action is taken,
the system will revert back to the Main Menu.
2. Press or to display the current time.
3. Press or to prepare the system for changes.
4. Press or to adjust and program the correct hour. Press
(

) to save the change and move on to program the minutes.
5. The current minutes will blink as an indication that it is ready.
Press or to adjust and program the minutes. Press (

)
to save the change and move on to program either AM or PM.
6. The current setting will blink as an indication that it is ready.
Press or to toggle between AM and PM. Once selected,
press (

) to save the change. The system will return to the “SET
TIME” Menu.
Programming the Date
To program the date, follow the steps below:
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current
settings will remain active.
1. Press ( ) until you get to the “DATE” Menu. The display will
scroll “SET DATE.” After the second scroll, if no action is taken,
the system will revert back to the Main Menu.
2. Press or and the current date will scroll. For example
“JAN 01 2016.”
3. Press or to display the year.
4. Press or to adjust and program the correct year. Press
(

) to save the change and move on to program the month.
5. The current month will blink as an indication that it is ready.
Press or to adjust and program the month. Press (

) to
save the change and move on to program the day.
6. The current day will blink as an indication that it is ready. Press
or to scroll through the days. When the day is selected,
press

to save the change. The system will return to the “SET
DATE” Menu.
Programming the Temperature Format
To program the temperature format, follow the steps below:
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current
settings will remain active.

Jacuzzi J-300 Series Specifications

General

Series	J-300 Series
Shell Material	Acrylic
Dimensions	84" x 84" x 36"
Water Capacity	350 gallons
Pumps	2
Lighting	LED lighting
Water Management	ClearRay Active Oxygen System