To Next Page
G
gabriellefischerAug 14, 2025
What to do if Jadever JWI-3100 show Overload condition?
- LLinda VasquezAug 14, 2025
If your Jadever Accessories are showing an overload condition, the solution is to remove the item causing the overload.
What to do if Jadever JWI-3100 show Overload condition?
If your Jadever Accessories are showing an overload condition, the solution is to remove the item causing the overload.
How to fix Jadever JWI-3100 when the initial zero point exceeds 30% of full load?
If the initial zero point of your Jadever Accessories exceeds 30% of the full load, here are the steps you can take: 1. Remove any obstacles or articles located under the pan. 2. If the problem persists, consider replacing the load cell or contacting the maintenance department for assistance.
What to do if Jadever JWI-3100 show Wrong calibration weights?
If your Jadever Accessories display an error related to wrong calibration weights, ensure that you place the correct test weights on the scale. The calibration value should also be below the full load capacity of the device.
How to resolve EEPROM failure in Jadever Accessories?
If you are experiencing EEPROM failure with your Jadever Accessories, the suggested solution is to re-weld the EEPROM. If the problem persists, contact the maintenance department for further assistance.
What to do if Jadever JWI-3100 exceed the zero range?
If your Jadever Accessories exceed the zero range, ensure that the item on the pan is within 2% of the full load.
What to do if Jadever JWI-3100 exceed tare or pre-tare range?
If your Jadever Accessories exceed the tare or pre-tare range, ensure that the tare value is within the range of 0 to the full load capacity.
What to do if Jadever JWI-3100' lower limit is higher than upper limit?
If the lower limit is higher than the upper limit on your Jadever Accessories, reset the weight limit value.
How to fix Model setting error in Jadever Accessories?
To fix a model setting error in Jadever Accessories, where the resolution should be within 300-300000, first adjust or reset the capacity and then adjust the resolution.
What to do if Jadever JWI-3100 Accessories exceed the A/D resolution range?
If your Jadever Accessories exceed the A/D resolution range: 1. Replace the A/D. 2. If the issue continues, replace the load cell or contact the maintenance department.
Detailed specifications and features of the JWI-3100 weighing indicator.
Description of symbols and indicators on the weighing indicator's LCD display.
Explanation of the function of each key on the weighing indicator's keypad.
Details about power source options, consumption, and battery charging indicators.
Instructions for connecting the load cell to the weighing indicator.
Step-by-step guide for assembling the upright pole and indicator.
Guide to setting the maximum weighing capacity and accuracy parameters.
Instructions for configuring various operational functions of the indicator.
Explanation of specific parameter values used in settings and configurations.
Configuration options for display brightness, power-saving modes, and auto-off timer.
Setup for weighing units, zero range, and different hold function modes.
Configuration for check weighing memory, buzzer alerts, and stable weighing.
Settings for connecting external devices and selecting print modes.
Basic procedure for weighing items on the scale.
How to tare containers and set preset tare values.
Procedure for comparing weights against upper and lower limits.
How to use the scale for counting items based on sample weight.
Commands for connecting to a computer and controlling the indicator.
Lists common error messages, their problems, and solutions.
General| Product Name | Jadever JWI-3100 |
|---|---|
| Category | Accessories |
| Display | LCD |
| Communication Interface | RS-232 |
| Type | Weighing Indicator |
| Capacity | Varies by model |
| Units | kg, lb |
| Power | AC adapter or rechargeable battery |
| Power Supply | AC 100V~240V |
| Operating Temperature | 0°C ~ 40°C |
| Humidity | < 85% RH |
| Weight Capacity | Varies by model |
