janitza UMG 509-PRO

To Next Page

To Previous Page

UMG 509-PRO

www.janitza.com

UMG 509-Pro

Power Quality Analyzer

Doc. no.: 2.059.011.2.s

10/2022

The German version is the original edition of the documentation.

Main Page

Table of Contents4
General10
Disclaimer10
Copyright Notice10
Technical Changes10
About this User Manual10
Meaning of the Symbols10
Defective Device/Disposal11
Safety12
Display of Warning Notices and Safety Information12
Hazard Levels12
Product Safety12
Dangers When Handling the Device13
Electrically Qualified Personnel14
Warranty in the Event of Damage14
Safety Information for Handling Current Transformers and Measurement Devices with Residual Current Measurement14
Handling Batteries/Accumulators15
Product Description16
Device Description16
Incoming Goods Inspection16
Intended Use16
Performance Characteristics17
EU Conformity Declaration18
FCC Declaration of Conformity18
Scope of Delivery18
Accessories18
Measuring Method19
Operating Concept19
Gridvis® Network Analysis Software19
Structure of the Device20
Front Panel and Display20
Rear View21
Mounting22
Installation Location22
Mounting Orientation22
Securing22
Grid Systems24
Three-Phase 3-Conductor Systems25
Three-Phase 4-Conductor Systems25
Nominal Voltages26
Installation28
Connection to a PC28
Ground Wire Connection29
Circuit Breaker29
Supply Voltage29
Measured Voltage30
Overvoltage30
Frequency30
Current Measurement31
Current Direction32
Summation Current Measurement32
Ammeter32
Measuring Variants33
Voltage Measurement33
Current Measurement34
Auxiliary Input35
Residual Current Detection36
Failure Monitoring36
Example: Insulation of the Residual Current Transformers37
Temperature Measurement38
Example Insulation of the Temperature Sensor38
Interfaces39
Shielding39
Interface40
Termination Resistors40
Profibus Interface41
Connecting the Bus Lines41
Bus Structure42
Ethernet Interface43
Digital Inputs and Outputs44
Digital Inputs44
S0 - Pulse Input45
Digital Outputs46
10. Operation48
Button Assignment48
Measuring Display "Home48
Measuring Display49
Main Values49
By-Values49
Selecting a Measuring Display50
Retrieving Additional Information51
Deleting Values51
Transient List52
Event List53
11. Configuration54
Languages54
Communication54
Ethernet (TCP/IP)55
Fieldbus55
Measurement56
Transformers56
Transients61
Events62
Mains Frequency64
Temperature64
System65
Password65
Reset66
Display67
Colors68
Enhancements69
PTP Configuration70
Important Modbus Parameters for the PTP Configuration of the Device70
Example: PTP Timing According to IEEE 1588-2008 and Clock Types71
12. Commissioning72
Supply Voltage72
Measured Voltage72
Frequency Measurement73
Direction of Rotary Field73
Measured Current74
Phasor Diagram Examples75
Residual Current75
Failure Monitoring (RCM)76
Alarm Status76
Overrange77
Control of the Power Measurement77
12.10 Control of the Communication77
12.11 Communication in the Bus System78
Rs-48578
12.11.2 Profibus79
12.12 Recording Configuration84
12.13 Digital Inputs/Outputs85
12.13.1 Digital Inputs85
12.13.2 Pulse Output85
13. Device Homepage88
Measured Values89
Brief Overview89
Detailed Measured Values90
Charts91
RCM - Residual Current Measurement91
Events92
Transients92
Power Quality93
Apps96
Push Service96
Information97
Device Information97
Display97
Downloads97
14. Service and Maintenance98
Repairs and Calibration98
Front Panel Foil98
Disposal98
Service98
Device Adjustment98
Calibration Intervals98
Firmware Update98
Battery99
15. Technical Data100
Supply Voltage100
Voltage and Current Measurement101
Residual Current Detection102
Temperature Measurement Input103
Digital Inputs and Outputs104
Interfaces105
Performance Characteristics of Functions106
Dimensional Drawings107
16. Procedure in the Event of a Malfunction108
17. Menu Navigation Overview110
Configuration Menu Overview110
Overview of Measuring Displays111
18. Connection Example114

janitza UMG 509-PRO - Page 2

Table of Contents

Other manuals for janitza UMG 509-PRO

Related product manuals