Why do my JBL EON 315 have no sound?
If your JBL speakers have no sound, it could be due to the speaker not being properly connected to an active AC power source. Make sure the speaker is connected and that the circuit is switched on. Alternatively, the power might not be switched on. Turn on the power and check if the power LED is illuminated.
What to do if my JBL EON 315 Speakers have no sound but are connected to power?
If your JBL speakers have no sound even when connected to a working power source, the issue might stem from a faulty or improperly connected power cable. Try re-seating the power cable at both ends, or substitute it with a known-good power cable. Another potential cause is a blown fuse. In this case, check the fuse and replace it with a spare fuse of the same type found in the holder.
General| Max SPL | 127 dB |
|---|---|
| Output Connectors | XLR loop-through |
| Coverage Pattern | 100° x 60° |
| LF Driver | 15 inch |
| HF Driver | 1" neodymium compression driver |
| Input Connectors | XLR / 1/4 inch combo jack |
| Suspension / Mounting | M10 suspension points |
| Dimensions | 685 mm x 438 mm x 366 mm |
| Weight | 15.9 kg (35 lbs) |
| Frequency Response | 60 Hz - 18 kHz |
Explains hazard symbols and their meanings for user safety.
Details necessary AC power specifications for operating the EON speaker.
Discusses amplifier operating temperature and auto-shutdown protection.
Provides guidelines for cleaning, handling, and protecting speakers from environmental factors.
Outlines crucial safety steps when using tripod or pole stands for speakers.
Warns about the risk of permanent hearing damage from high sound pressure levels.
Lists relevant safety and electromagnetic compatibility standards the product adheres to.
Details the UL standards and certifications met by the EON series.
Provides FCC rules and conditions for device operation and interference guidelines.
Lists the items included in the EON315 speaker system package.
Step-by-step instructions for safely powering on the EON speaker system.
Guidance on adjusting volume levels and gain structure for optimal sound.
Explains the function of the LIMIT LED and what to do if it stays illuminated.
Describes various scenarios and uses for the EON315 speaker system.
Lists the key technical features and capabilities of the EON315 speaker.
Explains how to adjust the input level to match sensitivity with source devices.
Details the balanced XLR and 1/4" TRS input connectors and their compatibility.
Describes the switch for selecting microphone or line-level input sensitivity.
Explains the EQ boost setting for enhanced low and high frequencies.
Describes the neutral EQ setting for unaltered frequency response and maximum level.
Details the EQ cut setting to reduce low frequencies, useful with subwoofers or for speech.
Describes the XLR output connector for sending audio signal from the EON315.
Explains the function of the SIGNAL LED, indicating a usable input signal.
Advises on speaker height for optimal audience sound coverage and minimizing feedback.
Guides on placement relative to turntables and in large/reverberant spaces.
Describes upright PA positioning and angled positions for stage monitoring.
Illustrates setting up a simple PA system using the speaker's built-in mixer.
Shows how to configure a small PA system with an external mixer.
Demonstrates connecting a speaker with a subwoofer using an external mixer.
Guides on expanding a PA system with more speakers using the built-in mixer.
Illustrates connecting speakers and subwoofers with a powered mixer.
Details setting up a PA system with a powered mixer and additional monitors.
Explains how to connect multiple speakers in series using the Mix/Loop function.
Shows gigging setups with main speakers and floor monitors using built-in mixers.
Explains balanced audio signal transmission, its benefits for noise rejection and cable length.
Describes unbalanced audio signal transmission and its limitations regarding noise.
Provides options for connecting unbalanced audio sources to EON speakers.
Illustrates common audio cables and connectors used for speaker systems.
Covers XLR microphone cables and balanced 1/4" to XLR cables for professional connections.
Details unbalanced 1/4" to XLR, 1/4" to RCA, and stereo split cables for various audio sources.
Defines who is covered under the JBL product warranty terms.
Details the scope of coverage and exclusions for JBL product warranties.
Explains the cost distribution for warranty repairs, including shipping.
Provides instructions on how to get service or repairs for JBL products.
Outlines limitations on implied warranties like merchantability and fitness for purpose.
Specifies that JBL's liability is limited to repair or replacement, excluding consequential damages.
To Next Page
