Jedia JMA-600A - Safety Instructions

1
SAFETY INSTRUCTIONS
Read all safety instruction before operating the JMA-Series amplifiers.
1. Install equipment as follow conditions.
Install at flat place, not bending curved.
Do not install near the water and moisture.
Locate power amplifier away from heat source, such as radiators
or other device that produce heat.
Do not drop objects or spill liquids into the inside of amplifier.
2. Keep in mind the following when connecting amplifier.
Connect the amplifier after reading of O/P manuals.
Connect each connection of amplifier perfectly, if not, it maybe
caused hum, damage, electric shock in case of mis-connecting.
To prevent electric shock, do not open top cover.
Connect the power cord with safety after check of AC power.
Amplifiers should be serviced by qualified service person.
FEATURES
Automatic variable speed FAN.
Over heating portection.
Load short circuit protection.
안󰼿전󰼿사󰼿항
제품을󰼿운용하기전에󰼿모든󰼿안전사항을󰼿읽어󰼿보십시오.󰼿
1.󰼿이런󰼿장소에󰼿설치하여󰼿주십시오.
진동이나󰼿경사가󰼿심하지󰼿않고󰼿바닥이󰼿평평한󰼿장소.
통풍이󰼿잘되고󰼿물기나󰼿습기가󰼿많지󰼿않은󰼿장소.
직사광선을󰼿받지󰼿않는󰼿장소󰼿또는󰼿난방기구(발열체)에서󰼿멀리󰼿떨어진󰼿장소.󰼿
인화성󰼿물질(화학약품)이󰼿없는󰼿장소.
2.󰼿설치시󰼿이런점을󰼿주의하십시오.
사용설명서󰼿시스템󰼿연결방법을󰼿완전히󰼿읽으신󰼿후에󰼿연결해󰼿주십시오.
각종󰼿연결선을󰼿완전하게󰼿연결해󰼿주십시오.
(주전원󰼿코드를󰼿뽑은󰼿상태에서󰼿연결.)
불완전한󰼿연결은󰼿잡음,󰼿제품의󰼿손상󰼿또는󰼿안전사고의󰼿원인이󰼿됩니다.
전기적󰼿충격󰼿또는󰼿감전사고의󰼿위험이󰼿있으므로󰼿뚜껑을󰼿열지󰼿말아주십시오.󰼿
주󰼿교류󰼿전원󰼿플러그를󰼿연결하기󰼿전에󰼿사용전압을󰼿확인하신󰼿후󰼿안전하게󰼿
연결하십시오.
제품을󰼿수리시는󰼿규정된󰼿부품과󰼿자격이󰼿있는󰼿사람이󰼿수리를󰼿하여야󰼿함.
특󰼿󰼿󰼿󰼿󰼿󰼿징󰼿
온도에󰼿따라󰼿팬󰼿속도󰼿자동조절.
과전류󰼿제한회로󰼿내장.
과열󰼿보호회로󰼿내장.
스피커󰼿선로󰼿쇼트󰼿검출회로󰼿내장.
Over current protection.
Power delay on circuit (soft start)
Ultra low distortion circuit.
XLR, 1/4" Phone jack(LINK) input connector.
5-WAY binding post, speakon connector.
Selective stereo, bridged mono.
전원󰼿공급󰼿지연회로󰼿내장.
XLR󰼿및󰼿1/4"󰼿폰잭(LINK)입력󰼿콘넥터󰼿채택.
5-WAY󰼿바인딩󰼿포스트󰼿및󰼿스피콘󰼿잭󰼿출력.󰼿
초저왜율󰼿회로로󰼿설계.
앰프󰼿운용은󰼿스테레오,󰼿브릿지󰼿모노로󰼿가능.
미려한󰼿디자인과󰼿완벽한󰼿신뢰성󰼿보장.