EasyManua.ls Logo

Jenn-Air JDS9860AAP - User Manual

Jenn-Air JDS9860AAP
62 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
16026016
March 2005
©2005 Maytag Services
This Base Manual covers general information
Refer to individual Technical Sheet
for information on specific models
This manual includes, but is
not limited to the following:
Service
This manual is to be used by qualified appliance
technicians only. Maytag does not assume any
responsibility for property damage or personal
injury for improper service procedures done by
an unqualified person.
JDS8850AAB/Q/S/W
JDS8850ACS/W
JDS9860AAB/P/W
JDS9860ACB/P/W
Dual Fuel
Slide-In
Range

Table of Contents

Other manuals for Jenn-Air JDS9860AAP

Questions and Answers

  • S
    santiagokaitlynAug 1, 2025
    What to do if my Jenn-Air Ranges burner won't ignite?
    • A
      ashley98Aug 1, 2025
      If the burner on your Jenn-Air Ranges isn't igniting, several factors could be at play. First, ensure your range is receiving 120 VAC by verifying the voltage at the wall outlet. A dirty electrode or burner cap can also prevent ignition, so try cleaning them. Other potential causes include faulty wiring or a bad connection at the burner electrode and electrode socket, micro switch contacts not closing, or a non-operative spark module. Check the wiring against the appropriate wiring diagram to ensure all terminals and connections are correct and tight. If the electrode is cracked or broken, replace it. Check the module according to testing procedures information.
  • P
    Paul MathewsAug 6, 2025
    How to fix Jenn-Air Ranges burners that won't ignite?
    • B
      Brianna BennettAug 6, 2025
      If the burners on your Jenn-Air Ranges aren't igniting and there's no spark, it could be due to several reasons. Start by cleaning the burner cap to ensure a good ground. Low gas pressure could also be the culprit; verify the pressure is 4" WCP for natural gas or 10" WCP for LP gas. Additionally, a clogged burner port can prevent ignition, so clean the burner cap. If these steps don't work, the spark module might be weak or has failed and should be replaced.
  • D
    David LongAug 10, 2025
    Why is my Jenn-Air Ranges bake element not working?
    • D
      dpayneAug 10, 2025
      If the bake element in your Jenn-Air Ranges isn't working, it could be due to an open bake element. Check the element for continuity and replace it if it has failed. Also, inspect for any loose or broken wire connections and ensure all connections are clean and tight, replacing any broken wires. Finally, verify 240 VAC at the bake element to check for an open bake relay.
  • S
    Sharon FernandezAug 16, 2025
    What to do if my Jenn-Air Ranges oven won't bake or broil?
    • P
      Patricia BrownAug 16, 2025
      If your Jenn-Air Ranges oven isn't operating in bake or broil mode, begin by checking for 120 VAC at the control. If there's no voltage, check the power source. If there is voltage to the control but no voltage from control to the ignitor, the control may need to be replaced. Also, inspect for any loose or broken wires, ensuring all connections are clean and tight; replace any broken wires.
  • O
    owellsAug 20, 2025
    Why is there no spark on my Jenn-Air Ranges ignitor?
    • J
      jmolinaAug 21, 2025
      If you're experiencing no spark or random sparks at one ignitor on your Jenn-Air Ranges, a few things could be the cause. Check for a cracked ignitor or pinched ignitor wire and replace the ignitor lead or electrode if needed. Poor continuity to the burner cap can also be an issue, so clean the burner cap and lead. Additionally, a bad ground connection or lack of continuity to ground or the ignitor can cause this problem. Tighten the ground connection and correct any breaks in the ground path from the ignitor path to the unit ground path. Finally, check for a cracked or broken ignitor extension lead and replace the ignitor lead if necessary.
  • A
    Amber HollowayAug 26, 2025
    What to do if Jenn-Air Ranges keeps sparking after being turned off?
    • H
      harrissamuelAug 26, 2025
      If your Jenn-Air Ranges continues to spark after the knob is turned to the OFF position, it could be due to a shorted valve switch or harness. In this case, replace the switch or harness. Also, check if the switch has slipped off the valve; carefully reposition the switch on the valve and rotate it from OFF to high several times to verify the switch is not broken.

Summary

Important Safety Information

General Safety Precautions

Covers anti-tip, gas leaks, and general appliance usage safety.

Troubleshooting Procedures

Troubleshooting Chart

Guide to diagnose and resolve common range problems.

Fault Code Chart

List of error codes and their corresponding component issues.

Testing Procedures

Component Testing

Procedures for testing individual range components.

Oven Control Testing

Steps to test the electronic oven control functions.

Appendix A: Installation Instructions

Electrical and Gas Supply Connection

Instructions for connecting the range to power and gas.

Installation Instructions (Model JDS9860 A**)

Anti-Tip Device Installation

Step-by-step guide for installing the anti-tip safety bracket.

Electrical Supply Connection

Instructions for connecting the range to the electrical power supply.

Gas Supply Connection

Procedures for connecting the range to the gas supply line.

Appendix B: Use Information

Care Information

Appendix C: LP Conversion Instructions

Jenn-Air JDS9860AAP Specifications

General IconGeneral
BrandJenn-Air
Model NumberJDS9860AAP
Product TypeRange
Cooktop TypeGas
Number of Burners5
Self-CleaningYes
ConvectionYes
Width30 inches
Burners5
ColorStainless Steel
Voltage240 V
Warranty1 Year Limited
Control TypeElectronic
Height36 inches
Fuel TypeDual Fuel (Gas Cooktop, Electric Oven)

Related product manuals