What to do if Jensen Stereo System radio will not turn on?
If your Jensen Stereo System radio won't turn on, try the reset button. Also, check the fuse, the 12V+ on the accessory wire (RED wire), and the ground connection.
How to fix Jensen JWM6A Stereo System remote control when it does not respond?
If your Jensen Stereo System unit does not respond to the remote control, first verify a clear line of sight for the IR signal. Then, check the batteries. Finally, confirm the remote IR sensor is plugged into the IR input, if applicable.
How to fix Jensen Stereo System if the radio will not turn ON or has no front panel operation?
If your Jensen Stereo System radio won't turn on or the front panel isn't working, try pressing the reset button. Check the fuse, ensure the 12V+ is connected to the accessory wire (RED wire), and verify the ground connection.
Why Jensen JWM6A unit does not respond to Remote Control?
If your Jensen Stereo System isn't responding to the remote control, first, make sure there's a clear line of sight for the IR signal. Then, check the batteries. If applicable, confirm that the remote IR sensor is plugged into the IR input.
Why Jensen JWM6A radio turns on, but there is no sound?
If your Jensen Stereo System turns on but produces no sound, first verify that the volume, fader/balance, and mute controls are correctly set. Try the reset button. Also, verify the proper speaker selection and connections. Finally, check for shorts or open circuits on the speaker wires. Note that if there's a short on the “A” channel, the “B & C” channels will continue to function, and vice versa.
What to do if Jensen JWM6A Stereo System CD/DVD does not play correctly?
If your Jensen Stereo System CD/DVD does not play correctly, ensure the disc is inserted correctly and is free from dirt and scratches. Try playing factory CDs. Inspect the radio’s chassis to verify the shipping screws have been removed. Check factory original CDs for compatibility warnings.
What to do if Jensen JWM6A CD/DVD does not load fully?
If the CD/DVD in your Jensen Stereo System does not load fully, ensure the unit has power and that no other CD/DVD is currently inside. Also, make sure the transport screw has been removed from the rear of the unit. The disc will load for several seconds and then eject if the transport screw hasn't been removed.
Why Jensen JWM6A Stereo System DVD plays sound but no video?
If your Jensen Stereo System DVD plays sound but no video, ensure the HDMI cable is correctly routed from the HDMI output to the input on the television.
How to improve AM or FM reception on Jensen Stereo System?
To improve AM or FM reception on your Jensen Stereo System, first verify that you are tuned to a valid station. Then, check your antenna connection on the rear of the stereo. You might also try using a different antenna.
What to do if Jensen JWM6A Stereo System radio turns ON, but there is no sound?
If your Jensen Stereo System turns on but produces no sound, first, check that the volume, fader/balance, and mute controls are properly adjusted. Try the reset button. Make sure the correct speaker selection and connections are in place. Also, inspect speaker wires for shorts or open circuits. If there's a short on the “A” channel, “B & C” channels will still work, and vice versa.
General| Brand | Jensen |
|---|---|
| Model | JWM6A |
| Category | Stereo System |
| Maximum Power (Watts x Channel) | 50 Watts x 2 |
| Woofer Size | 6.5 inches |
| Impedance | 4 Ohms |
| Mounting Type | Wall Mount |
| Bluetooth | Yes |
| USB Port | Yes |
| AM/FM Radio | Yes |
| Display | LCD |
| Clock | Yes |
| Frequency Response | 20Hz - 20kHz |
| Inputs | AUX, USB |
| Playable Media | MP3, WMA |
Provides essential safety warnings regarding power supply, disc mechanism handling, and avoiding moisture.
Crucial steps for safely disconnecting the vehicle battery prior to installation to prevent short circuits.
Provides a detailed diagram illustrating all required wiring connections for the unit's operation.
Details the available audio/video connection points on the system, including RCA, HDMI, and optical inputs.
Explains when and how to use the reset button to restore factory default settings.
Details how to connect and use the HDMI ARC function for TV audio output.
Guides on using auto seek tuning and storing/recalling favorite radio stations using preset buttons.
Explains how to navigate DVD menus and select audio or subtitle languages.
Overview of Bluetooth technology and detailed steps for pairing a Bluetooth-enabled device.
Guides on pairing a mobile device with the JWM6A and using the jControl app.
Details the function of each button on the remote control for various modes like Tuner, CD/DVD, and Bluetooth.
Continues the detailed explanation of remote control button functions across different operational modes.
Configure TV system, screen saver, resolution, password, rating, and default settings.
Set OSD, audio, subtitle, and menu languages, plus CEC control.
Configure audio output format, HDMI audio, and audio key settings.
Adjust brightness, contrast, hue, saturation, and sharpness of the display.
Tips for resolving radio reception issues and common problems.
To Next Page
