4. Machine specifications
4.1 Technical data
JPT-260:
Planing
Jointing width max 257 mm
Table length 1120mm
Height above floor 850mm
Fence size 1100 x 150mm
Fence tilt 0 - 45°
Depth of cut max.3 mm
Thicknessing
Thicknessing width max 256 mm
Thicknessing height 3 - 225 mm
Thicknessing table length 540mm
Min. length of work piece 150mm
Feed speed 5,5 m/min
Depth of cut max. 4,5 mm
Number of knives 3
Cutter block diameter 70 mm
No load speed n
o
5500 rpm
Cuts per minute 16500
Cutter knife length 260 mm
Cutter knife width 15 - 25mm
Cutter knife thickness 3mm
Dust port diameter 100mm
Overall (LxWxH) 1120x700x1000
Net Weight 170 kg
Mains 230V ~1/N/PE 50Hz
Output power 1,7 kW (2,3 HP) S1
Reference current 10 A
Extension cord (H07RN-F) 3x1,5mm²
Installation fuse protection 16A
Mains 400V ~3/PE 50Hz
Output power 1,7 kW (2,3 HP) S1
Reference current 3,5 A
Extension cord (H07RN-F) 4x1,5mm²
Installation fuse protection 16A
JPT-310:
Planing
Jointing width max 307 mm
Table length 1400mm
Height above floor 850mm
Fence size 1100 x 150mm
Fence tilt 0 - 45°
Depth of cut max.3 mm
Thicknessing
Thicknessing width max 307 mm
Thicknessing height 3 - 225 mm
Thicknessing table length 540mm
Min. length of work piece 150mm
Feed speed 7 m/min
Depth of cut max. 4,5 mm
Number of knives 3
Cutter block diameter 70 mm
No load speed n
o
5500 rpm
Cuts per minute 16500
Cutter knife length 310 mm
Cutter knife width 15 - 25mm
Cutter knife thickness 3mm
Dust port diameter 100mm
Overall (LxWxH) 1400x750x1000mm
Net Weight 230 kg
Mains 230V ~1/N/PE 50Hz
Output power 2,2 kW (3 HP) S1
Reference current 13 A
Extension cord (H07RN-F) 3x1,5mm²
Installation fuse protection 16A
Mains 400V ~3/PE 50Hz
Output power 2,2 kW (3 HP) S1
Reference current 5 A
Extension cord (H07RN-F) 4x1,5mm²
Installation fuse protection 16A
JPT-410:
Planing
Jointing width max 407 mm
Table length 1660mm
Height above floor 850mm
Fence size 1100 x 150mm
Fence tilt 0 - 45°
Depth of cut max.3 mm
Thicknessing
Thicknessing width max 407 mm
Thicknessing height 3 - 225 mm
Thicknessing table length 600mm
Min. length of work piece 150mm
Feed speed 7 m/min
Depth of cut max. 4,5 mm
Number of knives 3
Cutter block diameter 70 mm
No load speed n
o
5500 rpm
Cuts per minute 16500
Cutter knife length 410 mm
Cutter knife width 15 - 25mm
Cutter knife thickness 3mm
Dust port diameter 120mm
Overall (LxWxH) 1660x870x1000mm
Net Weight 315 kg
Mains 230V ~1/N/PE 50Hz
Output power 2,2 kW (3 HP) S1
Reference current 13 A
Extension cord (H07RN-F) 3x1,5mm²
Installation fuse protection 16A
Mains 400V ~3/PE 50Hz
Output power 3 kW (4 HP) S1
Reference current 6,5 A
Extension cord (H07RN-F) 4x1,5mm²
Installation fuse protection 16A
4.2 Noise emission
Determined according to EN 861
(Inspection tolerance 4 dB)
Work piece pine wood:
W=100mm, L=1000mm, moisture 8,5%
Planing:
Acoustic power level
(according to EN ISO 3746):
Idling LwA 89 dB(A)
Operating LwA 101 dB(A)
Acoustic pressure level
(according to EN ISO 11202):
Idling LpA 78 dB(A)
Operating LpA 96 dB(A)
Thicknessing:
Acoustic power level
(according to EN ISO 3746):
Idling LwA 92 dB(A)
Operating LwA 103 dB(A)
Acoustic pressure level
(according to EN 11202):
Operating position 1:
Idling LpA 74 dB(A)
Operating LpA 91 dB(A)
Operating position 2:
Idling LpA 84 dB(A)
Operating LpA 95 dB(A)
The specified values are emission
levels and are not necessarily to be
seen as safe operating levels.
Although there is a correlation between
emission and imission levels, these do
not constitute a basis for determining
the necessity of additional safety
measures.
Workplace conditions which could
influence the noise imission level
include the duration of resonance,
spatial particulars, other noise sources
etc. For example, the number of
machines and other work being
performed. The permissible workplace
levels can vary from country to
country.
This information is intended to allow
the user to make a better estimation of
the hazards and risks involved.
4.3 Dust emission
The planer thicknesser has been dust
emission inspected.
JPT-260, JPT-310:
At an air velocity of 20 m/s on the dust
port dia 100mm:
Vacuum pressure 900 Pa
Volume flow 565 m³/h
JPT-410:
At an air velocity of 20 m/s on the dust
port dia 120mm:
Vacuum pressure 950 Pa
Volume flow 810 m³/h
The machine meets a workplace dust
emission limit of 2 mg/m³.
To Next Page
Loading...
Need help?
General
