EasyManua.ls Logo

Jet JWL-1015VS - User Manual

Jet JWL-1015VS
45 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Operating Instructions and Parts Manual
10x15-inch Woodworking Lathe
Models JWL-1015, JWL-1015VS
model JWL-1015VS shown
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-719100
Ph.: 800-274-6848 Revision A1 02/2014
www.jettools.com Copyright © 2014 JET

Table of Contents

Other manuals for Jet JWL-1015VS

Preview: Operating Instructions
Operating Instructions40 pages
Preview: Assembly Instructions And Parts List
Assembly Instructions And Parts List2 pages

Questions and Answers

  • G
    Gail BradleyAug 12, 2025
    Why does my Jet JWL-1015VS motor fail to develop full power?
    • A
      Adam Miller MDAug 12, 2025
      The motor may fail to develop full power due to several reasons: the power line might be overloaded, requiring you to correct the overload condition; the wires in the power supply system could be undersized, suggesting an increase in supply wire size; there might be too many machines on the same circuit, so try shutting off other machines; or the motor itself could be worn, indicating that it needs replacement.
  • D
    Donna CoxAug 17, 2025
    What to do if my Jet JWL-1015VS motor or spindle stalls?
    • M
      Michael YangAug 18, 2025
      If the motor or spindle stalls, it could be due to several reasons. You might be taking an excessive cut, so reduce the depth of cut. The belt may be improperly adjusted, worn, or broken, requiring adjustment or replacement. The motor brushes could be worn or damaged, in which case you should replace them. Worn spindle bearings can also cause this issue, so replace the bearings. Finally, a worn motor may be the cause, indicating the need for a replacement.
  • D
    Dr. Michael PerkinsAug 23, 2025
    Why is my Jet JWL-1015VS vibrating so much?
    • S
      Sheri WalkerAug 23, 2025
      Excessive vibration in your Jet Lathe can stem from several causes. The workpiece might be warped, out of round, have a major flaw, or was improperly prepared for turning; correct this by planing or sawing the workpiece, or discard it and use a new one. Worn spindle bearings or a worn drive belt can also cause vibration, so replace them as needed. Check if the motor mounting fasteners are loose and tighten them. Lastly, ensure the lathe is on a flat surface.
  • L
    Lance BoydAug 29, 2025
    What to do if tools tend to grab or dig in on my Jet JWL-1015VS Lathe?
    • N
      Nina WashingtonAug 29, 2025
      If tools tend to grab or dig in, it might be because the tools are dull, so keep them sharp. Alternatively, the tool support might be set too low or too far from the workpiece; reposition the tool support height and/or closer to the workpiece. Finally, ensure you are using the correct tool for the operation.
  • S
    Sandra YoungSep 5, 2025
    How to fix tailstock movement when applying pressure on a Jet Lathe?
    • M
      Michael RodriguezSep 5, 2025
      If the tailstock moves when applying pressure, it could be that the cam lock nut needs adjusting, so tighten it. Another possibility is that the lathe bed and tailstock mating surfaces are greasy or oily; remove the tailstock and clean these surfaces with a cleaner/degreaser, then re-apply a light coat of oil to the lathe bed surface.

Jet JWL-1015VS Specifications

General IconGeneral
Spindle TaperMT2
Tailstock TaperMT2
Motor Power1/2 HP
Voltage115V
Distance Between Centers15 in
Spindle Bore0.625 in
Swing Over Bed10 in

Related product manuals