JRC JMR-5410-6X Simplified Instruction Manual

40 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

ISO 9001, ISO 14001 Certified

SEP. 2017 Edition 3CODE No.7ZPRD0955

MARINE RADARMARINE RADAR

EQUIPMENTEQUIPMENT

JMRJMR

-

54105410

-

6X/6XH6X/6XH

JMRJMR

-

54255425

-

6XH/7X/9X6XH/7X/9X

JMRJMR

-

54305430

-

S

JMRJMR

-

54725472

-

S

JMRJMR

-

54825482

-

S/SHS/SH

Not use the asbestos

For further information,contact:

URL Head office : http://www.jrc.co.jp/eng/

Marine Service Department

1-7-32 Tatsumi, Koto-ku, Tokyo 135-0053, Japan

　　　　　　　　　　　: tmsc@jrc.co.jp

　　　　　　　　　　　:

+81-50-3786-9201

e

-

mail

One

-

call

SIMPLIFIEDSIMPLIFIED

INSTRUCTIONINSTRUCTION

MANUALMANUAL

Table of Contents

Other manuals for JRC JMR-5410-6X

Instruction Manual640 pages

Questions and Answers:

B
Billy WoodwardAug 30, 2025
Why is the preheat countdown not showing on my JRC Marine Equipment's radar antenna?
- B
  brianna28Aug 30, 2025
  If the preheat count down of the radar antenna is not displayed on your JRC Marine Equipment, check the following: * Verify the connection with the radar antenna. * Ensure the safety switch of the radar antenna is set to ON. * If a solid-state radar antenna is connected, note that preheat count-down is not displayed for this type of antenna. If the issue persists, the radar antenna, internal wiring, or the processing unit (NDC-1678) may be faulty, requiring repair from the distributor.
M
Michelle TurnerAug 29, 2025
Why are water depth values not displayed on my JRC Marine Equipment?
- L
  Laura FosterAug 29, 2025
  If water depth values are not displayed on your JRC Marine Equipment, there are several potential causes: * The communication may not be set correctly, so ensure the communication settings are correct. * The power supply for the echo sounder might not be on; turn it on. * The connection with the echo sounder could be abnormal; verify the connection and, if an echo sounder is connected to the terminal board circuit (CQD-2322), check if the LED of the corresponding port is lit when data is received. If these steps don't resolve the issue, there may be a fault with the internal wiring or the processing unit (NDC-1678), requiring repair from the distributor.
K
Keith FloresAug 29, 2025
Why is wind data not displayed on my JRC Marine Equipment?
- C
  Christopher ReyesAug 29, 2025
  If wind direction/wind speed data is not displayed on your JRC Marine Equipment, there are several potential causes: * The communication may not be set correctly, so ensure the communication settings are correct. * The power supply for the anemoscope/anemometer might not be on; turn it on. * The connection with the anemoscope/anemometer could be abnormal; verify the connection and, if an anemoscope/anemometer is connected to the terminal board circuit (CQD-2322), check if the LED of the corresponding port is lit when data is received. If these steps don't resolve the issue, there may be a fault with the internal wiring or the processing unit (NDC-1678), requiring repair from the distributor.
K
Kristin HarrisAug 28, 2025
Why are rudder angles not displayed correctly on my JRC Marine Equipment?
- S
  sarah96Aug 29, 2025
  If rudder angles are not displayed correctly on your JRC Marine Equipment, there are several potential causes: * The communication may not be set correctly, so ensure the communication settings are correct. * The power supply for the rudder angle indicator might not be on; turn it on. * The connection with the rudder angle indicator could be abnormal; verify the connection and, if a rudder angle indicator is connected to the terminal board circuit (CQD-2322), check if the LED of the corresponding port is lit when data is received. If these steps don't resolve the issue, there may be a fault with the internal wiring or the processing unit (NDC-1678), requiring repair from the distributor.
M
Mercedes ScottAug 27, 2025
What to do if the radar antenna of my JRC Marine Equipment won't rotate?
- E
  edwardsethanAug 27, 2025
  If the radar antenna of your JRC Marine Equipment does not rotate even when the [TX/ST-BY] button is pressed, check these potential causes: * Verify the connection with the radar antenna. * Ensure the safety switch of the radar antenna is set to ON. * Check the power supply wiring from the power supply unit (NBD-945) inside the processing unit to the interface circuit (CMH-2452) to ensure power is being supplied to the radar antenna.
T
thomaskennedyAug 27, 2025
Why is the log not displayed correctly on my JRC Marine Equipment?
- A
  Angel MorseAug 27, 2025
  If log values are not displayed correctly on your JRC Marine Equipment, there are several potential causes: * The communication may not be set correctly, so ensure the communication settings are correct. * The power supply for the log equipment might not be on; turn it on. * The connection with the log equipment could be abnormal; verify the connection and, if connected to the terminal board circuit (CQD-2322), check if the corresponding LED blinks when the signal is received. If these steps don't resolve the issue, there may be a fault with the internal wiring or the processing unit (NDC-1678), requiring repair from the distributor.
C
Christopher AdamsAug 27, 2025
What to do if the radar antenna of my JRC Marine Equipment is not getting power?
- W
  William WilliamsAug 27, 2025
  If the power is not supplied to the radar antenna of your JRC Marine Equipment, check the following: * Verify the connection with the radar antenna. * Check for any abnormal connections with the radar antenna that may be causing overcurrent protection to activate in the power supply unit; remove any short-circuit causes. * Inspect the 24V DC output fuse; if it's blown, replace it after addressing the cause of the blowout. The fuse is F2. If the issue persists, there may be a fault with the internal wiring, the power supply (NDB-945) inside the processing unit, or the processing unit (NDC-1678) itself, requiring repair from the distributor.
B
brandongarzaAug 26, 2025
Why is the Gyro compass azimuth not displayed correctly on my JRC Marine Equipment?
- C
  Christopher HendersonAug 26, 2025
  If the azimuth of the Gyro compass is not displayed correctly on your JRC Marine Equipment, there are several potential causes: * The communication may not be set correctly, so ensure the communication settings are correct. * The power supply for the Gyro compass equipment might not be on; turn it on. * The connection with the Gyro compass equipment could be abnormal; verify the connection and, if connected to the terminal board circuit (CQD-2322), check if the corresponding LED is lit when the signal is received. If these steps don't resolve the issue, there may be a fault with the internal wiring or the processing unit (NDC-1678), requiring repair from the distributor.

JRC JMR-5410-6X Specifications

General

Peak Output Power	6 kW
Rotation Speed	24 rpm
Power Output	6 kW
Transmitter Frequency	9410 MHz
Display Type	LCD
Range	96 nm
Range Scales	3, 6, 12, 24, 48, 96 NM
Antenna Length	6 ft

Related product manuals

Preview: JRC JMR-5410-4X

JRC JMR-5410-4X

Preview: JRC JMR-7230-S

Preview: JRC JMR-7230-S3

JRC JMR-7230-S3

JRC JMR-7210-6X

JRC JMR-9210-6X

JRC JMR-7225-6X

JRC JMR-9225-6X

JRC JMR-9225-9X3