Juiced Bikes HYPERSCORPION 2021 - Advanced Controls

26 27
JBP-HYPERSCRP-MANUAL |
©
2021 JUICED BIKESJBP-HYPERSCRP-MANUAL |
©
2021 JUICED BIKES
SPEED
The speed indicator measures the speed of the bike. This value
is measured from the motor’s internal speed sensor. If you have
changed to a new re with a larger or smaller diameter than the
included re, you may need to manually adjust the wheel
speed seng.
CONTROLLER TEMPERATURE
The controller temperature is measured by a temperature
sensor mounted inside of the controller near the transistors.
The temperature displays on the screen in Celsius. When the
e-bike is under load, the controller’s temperature will increase.
The bike’s performance will begin to decrease when the
temperature exceeds 80 degrees Celsius.
TRIP DISTANCE
The trip distance counts up from zero. The distance is calculated
by each rotaon of the rear wheel. To reset the trip distance,
refer to “Reseng the Trip Counter” on page 24.
ADJUSTING PARAMETERS IN THE SETUP MENU
Adjust some of the parameters to control the behavior of your
e-bike.
TO ENTER THE SETTINGS MENU
Hold the “assist up” and “assist down” buons for about 3
seconds, then release. You will now enter the setup menu. Here
you can adjust a few sengs to control the behavior of the
e-bike.
AVAILABLE MENU OPTIONS
Unit Power Off Delay
Speed Limit NDW
Backlight Torque
Wheel Size Low Volts
NAVIGATING AND ENTERING A MENU SETTING
Use the “assist up” buon and “assist down” buon to navigate
through the menu. When you have selected a parameter you
wish to adjust, push the power buon once and you will enter
that seng.
You will then have the ability to adjust this seng’s value with
the “assist up” and “assist down” buons. When you have
adjusted the seng to your preference, push the power buon
to exit that seng. Connue pressing and releasing the power
buon unl you have exited out of the setup menu and return
to the main screen.
The parameters you have adjusted will not be programmed into
the system. Check to see if the sengs meet your needs with a
short test-ride. If the sengs need adjustment, follow the setup
instrucons again.
UNIT
The unit seng allows you to select between miles per hour
(mph) and kilometers per hour (kmh).
• mph: miles per hour
• km/h: kilometers per hour
OPERATION
SPEED LIMIT
The speed limit seng allows you to set the speed limit of the
bike.
The bike will accelerate up to the maximum speed specied in
this seng.
CLASSIFICATION SET POWER LIMIT SET PEDAL ASSIST
THROTTLE
OPERATION
USA Class 1 /
750W
Set NDW to 4 20 mph Not allowed
USA Class 2 /
750W*
Set NDW to 4
20 mph
(32 km/h)
20 mph
(32 km/h)
USA Class 3 /
750W
Set NDW to 4
28 mph
(45 km/h)
20 mph
(32 km/h)
Europe 250W / 25
km/h
Set NDW to 1
15.5 mph
(25 km/h)
Not Allowed
Europe S-Pedelec /
45 km/h
Set NDW to 4
28 mph
(45 km/h)
Not Allowed
Off-road mode** Set NDW to 5 30+ mph
30 mph
(48.2 km/h)
*default conguration **please refer to local laws & regulations before using
BACKLIGHT
Set the brightness of the backlight to the desired level.
WHEEL SIZE
Set the circumference of the re according to the parcular
wheel specicaon.
The wheel circumference is set in mm (millimeters).
“POWER OFF” DELAY
The “power o” delay mer lets you set the duraon that
bike will remain inacve before the electronics system will
automacally shut down to conserve power.
NDW
The NDW is the pedal assist level limiter. In the default
conguraon pedal assist has 5 modes:
ECO, 1, 2, 3, and SPORT
Adjust the maximum pedal assist level that can be selected by
changing the value of the NDW seng.
NDW SETTING
• 1 - The maximum assist level that can be selected is assist
level 1.
• 2 - The maximum assist level that can be selected is assist
level 2.
• 3 - The maximum assist level that can be selected is assist
level 3.
• 4 - The maximum assist level that can be selected is assist
level SPORT.
• 5 - The maximum assist level that can be selected is assist
level RACE.
TORQUE
The pedal assist system provides you with motor assistance
when you pedal. Choose if you want to use the torque sensor
OPERATION