Jungheinrich TFG 320 User Manual (English)

Questions and Answers:

N
Natalie DavisAug 22, 2025
Why won't the starter turn on my Jungheinrich Forklifts?
- M
  Michele CruzAug 23, 2025
  If the starter of your Jungheinrich Forklifts does not turn, it could be due to several reasons. First, make sure the travel direction switch is in neutral. If not, turn it to the neutral position. A low battery charge could also be the culprit; check the battery charge and charge it if needed. Additionally, inspect the battery terminals for looseness or oxidation; clean and grease them, and tighten the battery terminal cable. Check the starter cable for any damage and ensure it's properly tightened or replaced if necessary. Finally, see if the starter magnetic switch is jammed, and check if it audibly engages.
J
John FloresAug 26, 2025
Why is the engine temperature display in the red zone on my Jungheinrich Forklifts?
- C
  Charles DouglasAug 26, 2025
  If the engine temperature display on your Jungheinrich Forklifts is in the red zone, it could be due to several reasons. Check the engine oil level and top it up if necessary. Also, the radiator might be contaminated, so clean it. Ensure the coolant level is adequate, checking the engine radiator system for leaks and adding coolant if needed. Lastly, a slipping fan V-belt can cause overheating, so check the V-belt tension, tightening or replacing it as required.
R
Ronald GarciaAug 27, 2025
What to do if the engine oil indicator is lit during operation in Jungheinrich TFG 320?
- T
  Tim CalderonAug 27, 2025
  If the engine oil indicator is lit during operation, it indicates that the engine oil level is too low. Check the engine oil level and top it up if necessary.
R
robertwolfeAug 29, 2025
What to do if the starter does not turn in Jungheinrich TFG 320?
- A
  Alexandra GarciaAug 29, 2025
  If the starter doesn't turn, it could be due to several reasons: * The travel direction switch might not be in neutral. Turn the travel direction switch to neutral. * The battery charge might be too low. Check the battery charge and charge the battery if necessary. * The battery terminal cable could be loose or the terminals oxidized. Clean and grease the terminals, then tighten the battery terminal cable. * The starter cable might be loose or broken. Check the starter cable, and tighten or replace it as required. * The starter magnetic switch might be jammed. Check if the magnetic switch audibly engages.
K
Kelly MoodyAug 30, 2025
What to do if the engine temperature display is in the red zone in Jungheinrich TFG 320?
- J
  Jose PowellAug 30, 2025
  If the engine temperature display is in the red zone, it could indicate several problems: * The engine oil level might be too low; check and top up if necessary. * The radiator might be contaminated; clean it. * The coolant level might be too low; check the engine radiator system for leaks and add coolant if necessary. * The fan V-belt might be slipping; check the V-belt tension and tighten or replace it as required.
Z
zpriceSep 1, 2025
What to do if the transmission oil indicator is lit during operation in Jungheinrich Forklifts?
- S
  sydney13Sep 1, 2025
  If the transmission oil indicator is lit during operation, it suggests that the transmission oil level is too low. Check the transmission oil level and top up if necessary. Also, the radiator might be contaminated, so ensure you clean it.
K
Kyle AlexanderSep 3, 2025
What to do if the Jungheinrich Forklifts engine is running but the truck does not travel?
- M
  Matthew TurnerSep 3, 2025
  If the engine is running but the truck isn't moving, ensure that the travel direction switch is set to the required direction and that the parking brake is released.
M
Melissa ChangSep 4, 2025
Why is the lift speed too low in Jungheinrich TFG 320 Forklifts?
- M
  Mrs. Christine HoltSep 4, 2025
  If the lift speed is too low, it could be due to: * A hydraulic reservoir oil level that is too low. Check the hydraulic oil and top up if necessary. * A hydraulic reservoir discharge system that is contaminated or blocked. Clean or replace the hydraulic reservoir discharge system.
M
Mrs. Sarah JamesSep 6, 2025
What to do if the load cannot be raised to maximum height in Jungheinrich TFG 320?
- D
  Derek WilliamsSep 6, 2025
  If the load cannot be raised to the maximum height, it is likely that the hydraulic reservoir oil level is too low. Check the hydraulic oil and top up if necessary.
W
wilsonmichelleSep 7, 2025
What does it mean if the motor oil indicator is lit on my Jungheinrich TFG 320 Forklifts?
- L
  Lawrence CampbellSep 7, 2025
  If the motor oil indicator is lit during operation of your Jungheinrich Forklifts, it means that the motor oil level is too low. Check the engine oil level and top up if necessary.