JVC RX-807VTN

LL-L (€€€O% “ON)
ng Charac
You can name the S.E.A. manual preset patterns (SEA A to E} and
the TUNER preset channels (CH 1 to 20) as you wish. Up to five
characters can be entered.
1. Specify a S.E.A. manual preset pattern or a TUNER preset chan-
nel, then press the CHARACTER key
<To specify a S.E.A. pattern> <To specify a Tuner Preset Channel>
Use the S.E.A. PRESET key Use the numeric keys.
PRESET e 2
as
| The cursor at the teft blinks
If a character has already been
entered, the character blinks
Blinks
Note:
When a preset S.E.A. pattern has been called, press the CHARAC-
TER. key while the pattern is displayed (about 5 seconds). If the dis-
play is cleared before you press the CHARACTER key, press the
PRESET key
2. Select the appropriate characters with the UP and DOWN keys
Blinks
a racer aneur
CHARACTER Dawn -
Alphanumeric character order.
Blank
+— DOWN UP —-
PERE bo P ELT}
ROG GOR CICcr CREE
Ooh bP PPE
LT
3. Press the CHARACTER key to move to the next position
Repeat steps 2 and 3.
uaacten
RB OF
@ To alter the characters, move the blinking cursor to the desired
character for correction using the CHARACTER key
4. When the entry is complete, press the ENTER key to store it in
memory
= Fl
fo
I |
Le
—. —~
@ Recording
1. Press the SOURCE SELECTOR key for the desired source.
2. Operate the corresponding source equipment
<!f you select PHONO >
vor 1
CILIPE NITY
PPTL iNet
VOL 0 ae 10
Turntable and tape deck can be operated
Note:
The surround sound is recorded as a normal stereo sound even if
it is recorded with the SURROUND key is ON
= Three-Head Tape Decks
lf you have a three-head tape deck, you can use it to monitor the
sound being recorded. Connect the tape deck to the TAPE 2 termi-
nals and proceed as follows
1. Start recording the source onto the TAPE 2 deck
When the TAPE 2 MONITOR indicator is off, you hear the sound
of the source playing through the speakers.
2. Press the TAPE 2 key
ven 1 TAPE2 MONITOR
TAPE? CILAPT RATT
tH Li ivi
VOLO a 10
Now you hear the sound of the recording immediately as it is made
on the tape
@ By pressing the TAPE 2 key on and off, you can compare the sound
quality of the source with the quality of the tape recording being
made
Note:
Set the recording level from the tape deck. It can not be set with
the VOLUME control of this machine.
® Dubbing Tapes
Dubbing can be similarly performed between TAPE 1, TAPE 2, VCR
1 and VCR 2. When dubbing fram the TAPE 2 deck to another tape
deck, press the TAPE 2 key and the SOURCE SELECTOR key other
than the tape deck
<To record from TAPE 1 to TAPE 2>
1, Press the TAPE 1 key
VOR 1
a. Nae ah 4 6 |
Pet tof
oe ‘
2. Play back the TAPE 1 deck and record with the TAPE 2 deck.
<To record from TAPE 2 to TAPE 1>
1. Press the TAPE 2 key and a SOURCE SELECTOR key other than
TAPE 1
vor 1 TAPE2- MONITOR,
TAPER i i ;
VOL © an mee 10
2. Play back the TAPE 2 deck and record with the TAPE 1 deck.
NLAZO8-X¥u