Why Kaco blueplanaet 150 TL3 doesn't feed maximum power into the grid despite high radiation?
If your Kaco inverter isn't feeding maximum power into the grid despite high radiation, it could be due to particular ambient conditions. Ensure sufficient cooling of the unit. Also, remove any foreign bodies present on the device and clean the cooling fins.
What to do if the grid fuse trips with Kaco blueplanaet 150 TL3 Inverter?
If the grid fuse trips when using your Kaco Inverter, it may be because the grid fuse capacity is too low. Select a backup fuse with a capacity somewhat higher than the device’s maximum feed-in current. If this doesn't resolve the issue, there may be hardware damage, in which case you should contact KACO Service to test the hardware.
How to troubleshoot Kaco blueplanaet 150 TL3 when the LEDs do not light up?
If the LEDs on your Kaco Inverter do not light up, it could be due to the grid voltage not being available. Check whether the DC and AC voltages are within the permitted limits. If the issue persists, notify KACO Service.
What to do if Kaco blueplanaet 150 TL3 Inverter stops feeding into the grid shortly after being switched on?
If your Kaco Inverter stops feeding into the grid shortly after being switched on, even with sunlight present, the cause may be defective circuit-breakers in the device. Ensure that there is sufficient PV generator power. Another potential cause is a defective grid separation relay, which should be replaced by KACO Service. If neither of these solutions work, notify KACO Service.
Why is Kaco blueplanaet 150 TL3 Inverter active but not connected to the grid?
If your Kaco Inverter is active but not connected to the grid, it might be due to a grid-feed interruption caused by a grid fault. Change the grid parameters within the permitted operating limits.
What causes an impossible daily peak value on Kaco Inverter display?
If your Kaco Inverter displays an impossible daily peak value, it is likely due to faults in the grid. To reset the value immediately, switch the device off by disconnecting it from the grid and switching off the DC, then switch it back on.
What does 'Fault in fan 2' mean on my Kaco blueplanaet 150 TL3 Inverter?
If your Kaco Inverter displays 'Fault in fan 2', the fan is malfunctioning. Notify KACO Service! With a defective fan, the power is reduced to 50% to avoid the device being destroyed.
What does 'Fault in fan 3' mean on my Kaco Inverter?
If your Kaco Inverter displays 'Fault in fan 3', the fan is malfunctioning. Notify KACO Service! With a defective fan, the power is reduced to 50% to avoid the device being destroyed.
What to do if there is a fault in fan 1 of Kaco Inverter?
If there is a fault in fan 1 of your Kaco Inverter, it means that the fan is malfunctioning. Replace defective fan.
Why don't daily yields correspond to the yields on the feed-in meter of Kaco blueplanaet 150 TL3?
If the daily yields on your Kaco Inverter do not correspond to the yields on the feed-in meter, it is due to tolerances of the measuring elements in the device. No action is required.
General| Model | blueplanet 150 TL3 |
|---|---|
| AC voltage range | 310 V - 480 V |
| Number of MPP trackers | 1 |
| Protection Class | IP21 |
| Maximum DC Input Voltage | 1000 V |
| Nominal AC Voltage | 400 V |
| Operating Temperature Range | -25 °C to +60 °C |
| Warranty | 5 years |
| Type | String Inverter |
| Rated Output Power | 150 kW |
| Max. apparent AC power | 150 kVA |
| Nominal AC Output Power | 150 kW |
| Nominal AC Frequency | 50 Hz / 60 Hz |
To Next Page