Name: KB Electronics Penta KB Power KBRC-240D
Brand: KB Electronics
Rating: 4 (1 reviews)

To Next Page

To Previous Page

RECOMMENDED MOUNTING SCREW: 1/4" (M6)

[127.00]

5.000

[138.99]

5.472

[149.50]

5.886

[9.07]

0.357

[208.94]

8.226

[225.45]

8.876

[241.00]

9.488

KBRC-240D SHOWN WITH OPTIONAL

FORWARD-BRAKE-REVERSE AND AUTO/MANUAL SWITCHES

OLSTOPON

MANUAL

START

STOP

AUTO

REGENERATIVE

DC MOTOR SPEED CONTROL

PENTA-DRIVE

REV

FWD

NEMA-4X / IP-65

100

FIGURE 3 – MECHANICAL SPECIFICATIONS (Inches / [mm])

Table of Contents2
Simplified Operating Instructions4
Safety Warning5
Introduction5
General Performance Specifications6
Electrical Ratings6
Control Layout7
Enlarged View of Trimpots7
Mechanical Specifications8
II. Wiring Instructions9
Wiring Instructions9
Terminal Block Wiring Information9
Power Connections10
Full Voltage Field Connection (Shunt Wound Motors Only)10
Half Voltage Field Connection (Shunt Wound Motors Only)10
Field Connection (Shunt Wound Motors Only)11
Unidirectional Forward Main Speed Potentiometer Connection11
Unidirectional Reverse Main Speed Potentiometer Connection11
Bidirectional Main Speed Potentiometer Connection12
Bidirectional Main Speed Potentiometer Connection with Reversing Contacts12
Start/Stop Function Eliminated (Jumper Installed)12
Remote Start/Stop Switch Connection12
Voltage Following Connection13
Enable Circuit Connection13
Run Relay Output Contacts13
DC Tach-Generator Connection14
DC Tach-Generator Connection with Addition of R T14
AC Line Input Voltage Selection (J1 and J2)14
Motor Voltage Selection (J3)14
III. Setting Selectable Jumpers14
DC Tach-Generator Voltage Selection (J3)15
Motor Current Selection (J4)15
Analog Input Signal Voltage Selection (J5)15
Setting Motor Current15
Control Mode Selection (J6)16
Torque Mode Selection (J7)16
Current Limit Mode Selection (J8)16
Stop Mode Selection (J9)16
Run Relay Output Mode Selection (J10)16
IV. Mounting Instructions17
Recommended High Voltage Dielectric Withstand Testing (Hi-Pot Testing)17
Enable Jumper (J11)17
Hi-Pot Test Setup17
VI. Operation18
VII. Ac Line Fusing18
Linear Torque Mode18
Non-Linear Torque Mode18
Control Operation18
VIII. Trimpot Adjustments19
Offset (OFFSET) Trimpot Range19
Offset (OFFSET) Trimpot Adjustment19
Forward Acceleration (FACC) Trimpot Range19
Reverse Acceleration (RACC) Trimpot Range19
Forward Acceleration (FACC) and Reverse Acceleration (RACC) Trimpot Adjustment19
Maximum Speed (MAX) Trimpot Range20
Forward Current Limit (FWDCL) Trimpot Range20
Reverse Acceleration (REVCL) Trimpot Range20
IR Compensation (IR) Trimpot Range20
Response (RESP) Trimpot Range21
Deadband (DB) Trimpot Range21
Deadband (DB) Trimpot Adjustment21
Timed Current Limit (TCL) Trimpot Range21
IX. DIAGNOSTIC Leds22
Optional Accessories22
Limited Warranty24

Questions and Answers:

Need help?

Do you have a question about the KB Electronics Penta KB Power KBRC-240D and is the answer not in the manual?

KB Electronics Penta KB Power KBRC-240D Specifications

General

Brand	KB Electronics
Model	Penta KB Power KBRC-240D
Category	Media Converter
Language	English

KB Electronics Penta KB Power KBRC-240D User Manual

Table of Contents

Questions and Answers:

KB Electronics Penta KB Power KBRC-240D Specifications