Kemppi MinarcMig Evo 170 User Manual

11 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

MinarcMig

Evo 170, 200

Quick

guide

EN Quick guide

DA Kvik guide

DE Kurzanleitung

ES Guía rápida

FI Pikaohje

FR Guide de démarrage rapide

IT Guida rapida

NL Verkorte handleiding

NO Kom i gang

PL Szybki przewodnik

PT Guia de consulta rápida

RU Краткое руководство

SV Snabbguide

ZH 快速指南

Questions and Answers:

T
Theresa CobbAug 8, 2025
What to do if overheating indicator is illuminated on Kemppi Welding System?
- J
  John AtkinsonAug 8, 2025
  If the overheating indicator is on in your Kemppi Welding System, it means the machine has overheated and reached its maximum operating temperature. The thermostat has shut off the welding power. To fix this, let the unit cool down, and it will automatically reset. Also, make sure the cooling air flow is not blocked. If you have exceeded the machine’s duty cycle, wait for the indicator to turn off. Sometimes, this light can also mean there's an issue with the supply voltage being too low or too high.
L
Lisa WilliamsAug 16, 2025
Why my Kemppi MinarcMig Evo 170 Welding System produces poor welding results?
- D
  Daniel HuffAug 16, 2025
  Poor welding results with a Kemppi Welding System can be caused by several things. Make sure the wire feed is consistent. Check the welding power control and arc length settings. Verify the material selection setting. Ensure the earth return clamp is properly fixed to a clean point, and the cable and connections are undamaged. Check that the shielding gas is right for the wire material and that the gas flows correctly from the welding gun tip. Also, supply voltage should be even and not too low or high.
D
Devin EvansAug 23, 2025
What to do if the main switch indicator will not light up on Kemppi Welding System?
- K
  kyle55Aug 23, 2025
  If the main switch indicator on your Kemppi Welding System won't light up, it could be due to several reasons: there is no supply voltage light, the machine isn't connected to electricity, the mains supply fuses are blown, or there's an issue with the mains cable or plug. Check these components to solve the problem.
R
rachelbrownAug 31, 2025
How to fix wire feed entangles on Kemppi Welding System?
- M
  Melissa PrattAug 31, 2025
  If the wire isn't moving or the wire feed is tangling in your Kemppi Welding System, the feed rolls, wire liner, or contact tips might be defective. Inspect these parts and also check the wire mechanism adjustment isn't too tight or loose. Ensure the feed roll groove isn't too worn and the wire liner isn't blocked. Make sure the contact tip and wire liner match the wire size. Finally, check for spatter blocking the contact tip, ensuring the hole is open and undamaged.

Kemppi MinarcMig Evo 170 Specifications

General

Input Voltage	230 V
Output Current Range	10 - 170 A
Output Current	170 A
Process	MIG/MAG
Wire Diameter Range	0.6 - 1.0 mm
Frequency	50/60 Hz
Efficiency	85%
Protection Class	IP23
Duty Cycle at 40°C	40%

Related product manuals

Preview: Kemppi MinarcMig 180

Kemppi MinarcMig 180

Kemppi MinarcMig Adaptive 150

Preview: Kemppi Minarc Evo 180

Kemppi Minarc Evo 180

Preview: Kemppi MinarcTig Evo 200

Kemppi MinarcTig Evo 200

Preview: Kemppi Minarc Mig Evo 200

Kemppi Minarc Mig Evo 200

Preview: Kemppi Evo 150, 150VRD

Kemppi Evo 150, 150VRD

Preview: Kemppi Minarc 150

Kemppi Minarc 150

Preview: Kemppi MINARC 120

Kemppi MINARC 120

Kemppi Minarc 110

Preview: Kemppi Minarc 120AU

Kemppi Minarc 120AU

Kemppi MinarcTig250

Kemppi Minarc 120 AU