Kenmore 25376150410 - User Manual

For Medium (15-18.5K) + Heavy duty (22-28.5K) Air Conditioner
READ BEFORE INSTALLING UNIT
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp
edges that may be exposed:
Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to
move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over
an extended period of time.
Handle air conditioner with care. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp
metal fins of front and rear coils.
Make sure air conditioner does not fall during installation.
If a new electrical outlet is required, have the outlet installed by a qualified electrician before installing unit.
NOTE: DO NOT USE ANY SCREWS OTHER THAN THOSE SPECIFIED HERE.
Preliminary instructions:
Do the following before starting to install unit. See illustrations below.
Check dimensions of your unit to determine model type:
window sash seal
Heavy duty Medium
Capacity: 22,000-28,500 BTU 15,000-18,500 BTU
Unit Height: 18-5/8" 17-5/8"
Unit Width: 26-1/2" 23-5/8"
Min. Window Opening: 19-1/2" 18-1/2"
Min. Window Width: 31" 26-1/2"
Max. Window Width: 42" 40-1/2"
safety lock and
1/2" long hex
head screw
top angle
foam gasket
1. Check window opening size: the mounting parts
furnished with this air conditioner are made to install in
a wooden sill double-hung window. The standard parts
are for window dimensions listed above. Open sash to
a minimum of 19" (483mm). (FIG.l)
2. Check condition of window: all wood parts of window
must be in good shape and able to firmly hold the needed
screws. If not, make repairs before installing unit.
3. Check your storm windows: If your storm window
frame does not allow the clearance required, correct by
adding a piece of wood as shown (FIG.2), or by removing
storm window while room air conditioner is being installed.
FIG.1 _--sash
t
19" min
1/2" min inner sill |
storm window frame or
other obstruction
washer head
locking screw_
frame
(left)
side retainer
1/2" long
screws and
bottom rail Iocknuts --_
seat to unit %
/ Iocknut 3/4"\ _ _
long flat__.._. ,'_
head bolt \
sill angle
"_ bracket
window frame
support bracket assembly
(right)
FIG.2 _--sash
t
19" min
1/2" min _:1-1/2"mint
-- inner sill
...............................t
_'_oard thickness as
I _ required, along entire inner
window sill; fasten to inner
storm window frame or sill with two nails or screws.
other obstruction
2020219A2523

Summary

Window Mounting

Remove Air Conditioner from Cabinet

Steps to safely remove the AC unit from its internal cabinet.

Install Top Angle Rail and Side Retainers

Attaching essential angle rails and side retainers to the AC cabinet.

Assemble Window Filler Panels

Assembling the filler panels that seal gaps in the window.

Place Cabinet in Window

Positioning the main cabinet securely within the window opening.

Install Support Bracket

Installing brackets to provide stable support for the unit.

Extend Window Filler Panels and attach to top angle rail

Extending filler panels and attaching them to the top angle rail.

Attach Window Filler Panels to Window Frame

Fastening the filler panels to the window frame for a secure fit.

Install Window Sash Seal and Safety Lock

Installing seals for the window sash and safety locks.

Install Air Conditioner into Cabinet and Install Front Panel to Unit

Inserting the AC unit into the cabinet and reattaching the front panel.

Thru-The-Wall Installation

Select Wall Location

Choosing an appropriate location for wall installation based on criteria.

Prepare Wall

Cutting the necessary opening in the wall for the unit.

Prepare and Install Cabinet

Preparing and installing the main cabinet into the wall opening.

Masonry Construction

Steps for installing the unit in masonry walls.

Kenmore 25376150410 Specifications

General

Brand	Kenmore
Model Number	25376150410
Type	Window Air Conditioner
Room Size Coverage	Up to 350 sq. ft.
Voltage	115V
Number of Cooling Speeds	3
Number of Fan Speeds	3
Filter Type	Washable
Installation Type	Window
Cooling Capacity	8000 BTU
Dimensions (W x H x D)	14.5 x 21.5 inches