Need help?Do you have a question about the Kenwood KAC-526X and is the answer not in the manual?
Audio Specifications| Max Power Output (4 Ω) Normal | 200 W × 2 |
|---|---|
| Max Power Output (4 Ω) Bridge | 600 W × 1 |
| Rated Power Output (4 Ω) Normal (DIN45324, +B=14.4 V) | 100 W × 2 |
| Rated Power Output (4 Ω) Bridge (1 kHz, 0.8 % THD) | 300 W × 1 |
| Rated Power Output (2 Ω) Normal (1 kHz, 0.8 % THD) | 150 W × 2 |
| Frequency Response (+0, –1 dB) | 5 Hz ~ 50 kHz |
| Signal to Noise Ratio | 100 dB |
| Sensitivity (MAX) (rated output) | 0.2 V |
| Sensitivity (MIN) (rated output) | 5.0 V |
| Input Impedance | 10 kΩ |
| Low Pass Filter (12 dB/oct.) | 80 Hz |
General Specifications| Operating Voltage | 14.4 V |
|---|---|
| Current Consumption (1 kHz, 10% THD) | 28 A |
| Dimensions (W × H × D) | 220 × 52 × 300 mm |
| Weight | 3.0 kg |
Audio Specifications| Max Power Output (4 Ω) Normal | 70 W × 2 |
|---|---|
| Max Power Output (4 Ω) Bridge | 200 W × 1 |
| Rated Power Output (4 Ω) Normal (DIN45324, +B=14.4 V) | 35 W × 2 |
| Rated Power Output (4 Ω) Bridge (1 kHz, 0.8 % THD) | 100 W × 1 |
| Rated Power Output (2 Ω) Normal (1 kHz, 0.8 % THD) | 50 W × 2 |
| Frequency Response (+0, –1 dB) | 5 Hz ~ 50 kHz |
| Signal to Noise Ratio | 100 dB |
| Sensitivity (MAX) (rated output) | 0.2 V |
| Sensitivity (MIN) (rated output) | 5.0 V |
| Input Impedance | 10 kΩ |
| Low Pass Filter (12 dB/oct.) | 80 Hz |
General Specifications| Operating Voltage | 14.4 V |
|---|---|
| Current Consumption (1 kHz, 10% THD) | 16 A |
| Dimensions (W × H × D) | 220 × 52 × 160 mm |
| Weight | 1.6 kg |
Precautions to prevent fire, personal injury, and ensure proper operation.
Guidelines for safely cleaning the unit's surface.
Details of accessories provided with the unit.
Important safety and operational cautions for installation.
Information on using optional extension cables.
Description of the RCA cable ground lead terminal function.
Explanation of the filter switch for speaker output signals.
How to select the amplification method of input signals.
Guide for setting the input sensitivity control.
Describes the power indicator and its relation to protection.
Instructions for connecting RCA cables to the unit.
How to connect speaker level inputs from a car stereo.
Important cautions for connecting speaker level inputs.
Connecting power control (REMOTE) and speaker output cables.
Connecting battery and ground cables to power terminals.
How to bridge-connect speakers and impedance requirements.
Example setup for a full-range 2-channel system.
Example setup for a high-power 2-channel system.
Example setup for a 2-channel system with a subwoofer.
Explanation of the Tri-mode system and frequency division.
Troubleshooting steps for no sound or sound from one side.
Troubleshooting for output level being too small or too large.
Troubleshooting for bad or distorted sound quality.
Technical specifications for the audio section of the unit.
General technical specifications including dimensions and weight.
To Next Page
