EasyManua.ls Logo

Kenwood KD-75F User Manual

Kenwood KD-75F
8 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
K
D-75F
KE
NWO
O
D
KD-75FC
(FCL)
INSTRUCTION
MANUAL
©PRINTED
IN
JAPAN
B50-6116-00(K,
P, U,
M,
UE,
AXT)
87/654321
86/1211109876543
For
your
records
Record
the
serial
number,
found
on
the
back
of
the
unit,
in
the
spaces
designated
on
the
warranty
card,
and
in
the
space
provided
below.
Refer
to
the
model
and
serial
numbers
whenever
you
call
upon
your
dealer
for
information
or
service
on
this
product.
Model
Serial
Number.
Unpacking
Unpack
the
unit
carefully
and
make
sure
that
all
accessories
are
put
aside
so
they
will
not
be
lost.
Examine
the
unit
for
any
possibility
of
shipping
damage.
If
your
unit
is
damaged
or
fails
to
operate,
notify
your
dealer
im-
mediately.
If
your
unit
was
shipped
to
you
directly,
notify
the
shipping
company
without
delay.
Only
the
consignee
(the
person
or
company
receiving
the
unit)
can
file
a
claim
against
the
carrier
for
shipping
damage.
We
recommend
that
you
retain
the
original
carton
and
pack-
ing
materials
for
use
should
you
transport
or
ship
the
unit
in
the
future.
Before
applying
power
Important!
U.S.A.,
and
Canada
These
units
are
not
equipped
with
an
AC
voltage
selec-
tor
switch
and
the
discussion
of
such
a
switch
that
follows
should
be
disregarded.
All
other
countries
Units
shipped
to
countries
other
than
U.S.A.
and
Canada
are
equipped
with
an
AC
voltage
selector
switch
on
the
rear
panel.
Refer
to
the
following
paragraph
for
the
proper
setting
of
this
switch.
a
Rear
panel
safety
precautions
CAUTION
RISK
OF
ELECTRIC
SHOCK
DO
NOT
OPEN
VICE
PERSONNEL.
AC
voltage
selection
This
unit
operates
on
120
volts
or
220
—
240
volts
AC.
The
AC
voltage
selector
switch
on
the
rear
panel
is
set
to
the
voltage
that
prevails
in
the
area
to
which
the
unit
is
shipped.
Before
connecting
the
power
cord
to
your
AC
outlet,
make
sure
that
the
setting
position
of
this
switch
matches
your
line
voltage.
If
not,
it
must
be
set
to
your
voltage
in
accordance
with
the
following
direction.
Note:
Our
warranty
does
not
cover
damage
caused
by
excessive
line
voltage
due
to
improper
setting
of
the
AC
voltage
selector
switch.
1-2
220
-
240
V~
setting
1-1
Fig.
1
1.
Before
plugging
in
this
unit,
make
sure
that
the
posi-
tion
of
the
AC
voltage
selector
conforms
to
your
line
(mains)
voltage.
If
not,
it
must
be
reset.
See
Fig.
2.
To
reset
the
selector,
slide
the
stopper
plate
to
the
opposite
side
with
a
screwdriver
or
other
pointed
tool.
See
Fig.
1-2.
3.
Insert
the
power
cord
securely.
See
Fig.
1-3.
WARNING:
TO
PREVENT
FIRE
OR
ELECTRIC
SHOCK,
DO
NOT
EXPOSE
THIS
AP-
PLIANCE
TO
RAIN
OR
MOISTURE.
CAUTION:
TO
REDUCE
THE
RISK
OF
ELECTRIC
SHOCK,
DO
NOT
REMOVE
COVER
(OR
BACK).
NO
USER-SERVICEABLE
PARTS
INSIDE.
REFER
SERVICING
TO
QUALIFIED
SER-
persons.
—_—
The
lightning
flash
with
arrowhead
symbol,
within
an
equilateral
triangle,
is
intended
to
alert
the
user
to
the
presence
of
uninsulated
‘’dangerous
voitage’’
within
the
product’s
enclosure;
that
may
be
of
sufficient
magnitude
to
constitute
a
risk
of
electric
shock
to
The
exclamation
point
within
an
equilateral
triangle
is
intended
to
alert
the
user
to
the
presence
of
important
operating
and
maintenance
(servicing)
instructions
in
the
literature
accompanying
the
appliance.
Question and Answer IconNeed help?

Do you have a question about the Kenwood KD-75F and is the answer not in the manual?

Kenwood KD-75F Specifications

General IconGeneral
Overhang15mm
Output Level2.5mV (1kHz, 5cm/sec)
Speeds33 1/3, 45 rpm
PlatterAluminum die-cast
TonearmStatic balance type
Cartridge weight range4 to 10g
Frequency Response20 Hz - 20 kHz

Summary

For Your Records

Unpacking the Turntable

Before Applying Power

Rear Panel Safety Precautions

AC Voltage Selection

Parts Nomenclature

Tonearm Retaining Screw

Reassembly and Connection

Placing Turntable Platter and Rubber Mat

Instructions for placing the turntable platter and rubber mat on the center spindle.

Connections

Guide for connecting RCA pin-plug cords, ground lead, and AC cord to the unit.

Connecting the Synchro Terminal

Details on connecting the synchro terminal for synchro recording with related units.

Operating Instructions

Before Playing Records

Notes on using the auto size selector and sensor sensitivity for record playback.

Automatic Playback

Steps for initiating automatic playback and how the auto size selector functions.

Manual Playback

Program Playback

Skipping to the Next Tune

Direct Tune Selection

Suspending Playback

Repeat Playback

Synchro Operation

Record Key

Explanation of the RECORDING key's function for synchro recording.

Combination with Control Amplifier (KC-105)

Details on synchro dubbing operations with the KC-105 control amplifier.

Combination with Receiver (KR-V95R, KR-V75R, KR-V55R)

Using the remote control PHONO button for play/cut operation.

Maintenance

Motor Lubrication

Information on the motor's permanently-lubricated bearings and lifespan.

Periodic Check-up

Recommendation for periodic check-ups to ensure long service life.

Stylus Replacement

Instructions and diagrams for replacing the stylus.

Notes on Installation

Guidelines for proper installation location and environmental conditions.

Safety Precautions

Warnings regarding electric shock and handling the power cord.

Cleaning

Recommendations on cleaning materials for the cabinet.

Note on Record Playback

List of record types that may cause playback issues in certain modes.

In Case of Difficulty

Specifications

An Example of Synchro Connection

Related product manuals