What to do if my Kenwood Car Receiver sound cannot be heard?
If you cannot hear any sound from your Kenwood Car Receiver, try these solutions: First, adjust the volume to make sure it's at an audible level. Next, inspect the cords and connections to ensure they are properly connected. Finally, clean the connectors to remove any dirt or debris that might be interfering with the sound.
What to do if Bluetooth pairing cannot be made on Kenwood Car Receiver?
If you're having trouble pairing a Bluetooth device with your Kenwood Car Receiver: * Ensure you've entered the same PIN code on both devices. * Try deleting the pairing information from both the receiver and the Bluetooth device, and then attempt the pairing process again.
What to do if setting/deleting the remote control ID is unsuccessful on Kenwood Car Receiver?
If setting or deleting the remote control ID is unsuccessful and you see “SET ERROR” or “DEL ERROR” on your Kenwood Car Receiver, turn the power off, then turn it back on, and try the operation again.
Why does my Kenwood Car Receiver say 'MISWIRING CHECK WIRING THEN PWR ON'?
If your Kenwood Car Receiver displays the message “MISWIRING CHECK WIRING THEN PWR ON”, turn the power off. Then, check to ensure the terminals of the speaker wires are properly insulated. Turn the power back on.
What does “CHECK ANTENNA” mean on my Kenwood Car Receiver and how to fix it?
If your Kenwood Car Receiver displays “CHECK ANTENNA”, it means you should check that the antenna and its connection are in good condition.
What to do if my Kenwood Car Receiver disc cannot be ejected?
If the disc cannot be ejected from your Kenwood Car Receiver, press and hold the M button to forcibly eject the disc, being careful not to drop it. If this does not solve the problem, reset the unit.
Why does my Kenwood Car Receiver say “NO SIGNAL”?
If your Kenwood Car Receiver displays “NO SIGNAL”, make sure the antenna is mounted outside the vehicle.
What does “NO MUSIC” mean on Kenwood Car Receiver?
If your Kenwood Car Receiver displays “NO MUSIC”, connect a USB device that contains playable audio files.
How to fix echo or noise during a phone conversation on my Kenwood Car Receiver?
If you experience echo or noise during phone conversations using your Kenwood Car Receiver, try the following: 1. Adjust the microphone unit’s position. 2. Check the [ECHO CANCEL] setting.
What does “USB HUB IS NOT SUPPORTED” mean on Kenwood Car Receiver?
If your Kenwood Car Receiver displays “USB HUB IS NOT SUPPORTED”, it means that the unit cannot support a USB device connected via a USB hub.
Important warnings, cautions, and preparation steps before operating the unit.
Guides through initial setup, language selection, clock setting, and basic configurations.
Instructions for tuning, searching, and storing radio stations.
How to play music from CDs, USB devices, iPods, and Android phones.
Instructions for connecting the tuner, activation, and starting SiriusXM listening.
Steps to pair Bluetooth devices, including phone and audio.
How to receive calls, manage calls, and improve voice quality.
Streaming audio and managing connected Bluetooth audio devices.
Provides solutions for common problems encountered during operation of various features.
General| Type | Car Receiver |
|---|---|
| Channels | 4 |
| RMS Power Output | 22 Watts |
| Peak Power Output | 50 Watts |
| Bluetooth | Yes |
| USB Port | Yes |
| Auxiliary Input | Yes |
| CD Player | Yes |
| AM/FM Tuner | Yes |
| Display Type | LCD |
| Button Illumination | Variable Color |
| Wireless Audio Streaming | Yes |
| Hands-free Calling | Yes |
| MP3 Playback | Yes |
| WMA Playback | Yes |
| AAC Playback | Yes |
| WAV Playback | Yes |
| FLAC Playback | Yes |
| EQ Settings | 13-Band Graphic EQ |
| Preset EQ | Yes |
| Subwoofer Control | Yes |
| Subwoofer Output | Yes |
| Radio Data System (RDS) | Yes |
To Next Page