Kenwood TS-B2000 User Manual (English)

Other manuals for Kenwood TS-B2000

Instruction Manual152 pages

Operation Procedure3 pages

Specifications10 pages

Questions and Answers:

T
Todd HermanSep 15, 2025
Why is my Kenwood Car Receiver not receiving any signals?
- G
  Gerald FrederickSep 15, 2025
  If you are not receiving signals or the receive sensitivity seems poor on your Kenwood Car Receiver, check the following: * Ensure the SQL control is not fully clockwise; turn it counterclockwise. * Make sure the Attenuator function is OFF by pressing [ATT/ F LOCK]. * Verify you are not in transmit mode by pressing [SEND] or releasing Mic[PTT]. * Check the receive bandwidth settings. * Select the correct antenna connector (ANT 1 or ANT 2) by pressing [FUNC],[AT/ ANT1/2]. * Ensure the receive preamplifier is ON by pressing [PRE/ LOCK A].
K
Kaitlyn SampsonAug 25, 2025
How to unlock frequency on Kenwood Car Receiver?
- K
  Kevin RodriguezAug 25, 2025
  If the frequency cannot be changed on your Kenwood Car Receiver, the Frequency Lock function or Lock All function may be ON. To resolve this, press [FUNC],[F LOCK] to switch the Frequency Lock function OFF. Alternatively, press [FUNC],[LOCK A] to switch the Lock All function OFF.
N
nbrockAug 25, 2025
What to do if Kenwood TS-B2000 will not power up?
- M
  Mr. James WallaceAug 26, 2025
  First, ensure the DC power supply is switched ON. Inspect the power cable, confirming correct polarities (Red: positive (+); Black: negative (–)). Check that the connections to the DC power supply are secure. Finally, check the power cable fuse. If it's open, find the cause, correct any issues, and install a new fuse of the specified rating.
N
nellisAug 26, 2025
What to do if Kenwood Transceiver received signals are totally unintelligible?
- D
  David WilliamsAug 27, 2025
  If received signals are unintelligible, the wrong modulation mode may be selected. Press [LSB/USB], [CW/FSK], or [FM/AM] to select the correct modulation mode.
V
Victoria HamptonAug 27, 2025
What to do if Kenwood Transceiver has low transmit power?
- O
  ostevensAug 27, 2025
  If your transceiver has low transmit power, first, if you are in SSB or AM mode, increase the microphone gain. Second, check antenna connections to confirm that the antenna tuner is reporting a low SWR, as poor antenna system connections can cause high SWR.
V
Victoria AndersonSep 9, 2025
Why Kenwood TS-B2000 Transceiver does not function normally after switching ON the power?
- K
  kimberlyatkinsonSep 9, 2025
  If the transceiver does not function normally after switching ON the power, it could be due to: * The input voltage being outside the range of 13.8 V DC ±15% (11.7 to 15.8 V DC). Correct the input voltage or use a 12 to 16 V battery. * The microprocessor malfunctioning. In this case, do a Partial Reset. If the problem remains, do a Full Reset.
J
Joseph ReynoldsSep 8, 2025
What to do if Kenwood TS-B2000 linear amplifier does not operate?
- L
  Lisa KempSep 8, 2025
  If the linear amplifier does not operate, first, check if the linear amplifier control relay is OFF and, if so, change Menu No. 39 to ON. Second, inspect the REMOTE connector wiring and correct as necessary.
R
Ryan PattersonSep 8, 2025
Why after switching ON Kenwood TS-B2000 Transceiver, “14.000.00 MHz USB” appears and all data is lost?
- T
  Thomas HesterSep 9, 2025
  If, after switching ON the transceiver, “14.000.00 MHz USB” appears and all data is lost, the backup lithium battery voltage may be too low. Have a new battery installed by your dealer or at a KENWOOD Service Center.
A
Austin FisherSep 2, 2025
What to do if Kenwood TS-B2000 internal tuner is bypassed immediately after tuning is started?
- A
  acomptonSep 2, 2025
  If the internal tuner is bypassed immediately after tuning starts, the SWR of the antenna system may be too high. Adjust the antenna system to lower the SWR.
R
Rachel AdamsAug 31, 2025
What to do if Kenwood TS-B2000 Transceiver memory scan will not start scanning?
- C
  Christopher WhiteAug 31, 2025
  If Memory Scan won't start, first, adjust the SQL control to just eliminate background noise. Second, ensure at least two memory channels are unlocked. Third, make sure data is stored in at least two memory channels.