Keysight PNA-X N5241A - PNA Series Test Set and Power Configuration Options

10 | Keysight | PNA Family Microwave Network Analyzers - Congurations Guide
The PNA is an integrated vector network analyzer featuring a
built-in S-parameter test set, one or two synthesized sources
used for device stimulus, a solid-state drive, USB interfaces, and
a 10.4” LCD touch screen display. The N5221A and the N5222A
have 50 ohm, ruggedized 3.5 mm (m) test ports. The N5224A
and the N5225A have 50 ohm, ruggedized 2.4 mm (m) test ports.
The N5227A has a 50 ohm, ruggedized 1.85 mm (m) test ports.
Included with each instrument is a mouse, keyboard (U.S. style),
and one day of on-site productivity assistance (PS-S20-PNA).
A test set and power conguration option is mandatory, choose
one of the following:
2-ports, single source, base conguration (Option
200/210)
The 2-port with base conguration has no front-panel access
loops.
2-ports, single source, with congurable test set
(Option 201)
The 2-port congurable test set comes with six front-panel ac-
cess loops. The loops provide access to the signal path between
(a) the source output and the reference receiver, (b) the source
output and directional coupler thru arm and (c) the coupled arm
of the directional coupler and the port receiver at all ports. Also
included is a solid-state internal RF transfer switch in the R1
reference-receiver path.
2-ports, single source, with extended power range
(Option 217)
The 2-port test set with extended power range comes with a
congurable test set, source and receiver attenuators at each
port. For N5221/22A, the source attenuators are 65 dB in 5 dB
steps and the receiver attenuators are 35 dB in 5 dB steps. For
N5224/25A, the source attenuators are 60 dB in 10 dB steps and
the receiver attenuators are 35 dB in 5 dB steps. Also included
is a solid-state internal RF transfer switch in the R1 reference-
receiver path. This conguration is not available on N5227A.
2-ports, single source, with extended power range
and bias-tee (Option 219)
The 2-port test set with extended power range and bias-tee
comes with a congurable test set, source and receiver attenu-
ators, and bias-tee at each port. For N5221/22A, the source
attenuators are 65 dB in 5 dB steps and the receiver attenuators
are 35 dB in 5 dB steps. For N5224/25A, the source attenuators
are 60 dB in 10 dB steps and the receiver attenuators are 35 dB
in 5 dB steps. For N5227A, both source and receiver attenuators
are 50 dB in 10 dB steps. Also included is a solid-state internal
RF transfer switch in the R1 reference-receiver path.
PNA Series test set and power conguration options
1
Te st port 1 Test port 2
A B
R1
R2
Source
OUT 1OUT 2
Pulse
modulator
To receivers
LO
Pulse generators
RABC D
IF inputs
rear panel
R1
R2
35 dB
65 dB 65 dB
A
35 dB
B
Source
OUT 1OUT 2
Pulse
modulator
To receivers
LO
Pulse generators
RABC D
IF inputs
rear panel
Te st port 1
R1
Te st port 2
R2
A B
Source
OUT 1OUT 2
Pulse
modulator
To receivers
LO
Pulse generators
RABC D
IF inputs
rear panel
Te st port 1
R1
Te st port 2
R2
35 dB
65 dB 65 dB
A
35 dB
B
Source
OUT 1OUT 2
Pulse
modulator
To receivers
LO
Pulse generators
RABC D
IF inputs
rear panel
1. The block diagrams shown above include hardware that must be ordered
as separate options, such as pulse generators (Option 025), pulse modu-
lators (Options 021 and 022), and IF access (Option 020). In addition, the
attenuator values vary by model number. Refer to the product data sheet
for the correct block diagram for a specic model.