Need help?Do you have a question about the Keysight ENA Series and is the answer not in the manual?
General| Number of Ports | 2 or 4 |
|---|---|
| Dynamic Range | > 123 dB (typical) |
| Interface | LAN, USB, GPIB |
| Frequency Range | 9 kHz to 8.5 GHz |
| Trace Noise | 0.004 dB rms |
| IF Bandwidth | 1 Hz to 3 MHz |
| Impedance | 50 Ohm |
| Connector Type | Type-N |
| Display | LCD |
Acknowledges trademarks used in the manual.
Details the warranty terms and conditions for the product.
Essential safety precautions for operating and maintaining the instrument, including grounding, atmosphere, live circuits, and part substitution.
Describes the structure and organization of the service manual.
Identifies the specific instrument covered by this manual.
Lists the necessary equipment for performing maintenance and tests.
Introduces the chapter on performance test procedures.
Lists the test equipment needed for all performance tests.
Measures the DC source output voltage accuracy for control lines.
Measures the limited current value for each control line.
Checks Load Match, Insertion Loss, and Isolation for Switch 1 ports.
Checks Load Match, Insertion Loss, and Isolation for Switch 2 ports.
Checks Load Match, Insertion Loss, and Isolation for Switch 3 ports.
Checks Load Match, Insertion Loss, and Isolation for Switch 4 ports.
Checks Load Match, Insertion Loss, and Isolation for Switch 5 ports.
Checks Load Match, Insertion Loss, and Isolation for Switch 6 ports.
Checks Load Match, Insertion Loss, and Isolation for Switch 7 ports.
Checks Load Match, Insertion Loss, and Isolation for Switch 8 ports.
Checks Load Match, Insertion Loss, and Isolation for Switch 9 ports.
Checks Load Match, Insertion Loss, and Isolation for Switch 10 ports.
Measures the current meter accuracy in control line paths.
A record for documenting performance test results.
Introduces the troubleshooting procedures for the E5092A.
Provides a guide to troubleshooting the E5092A.
A flowchart to guide the troubleshooting process.
Steps for troubleshooting power supply issues.
Guide to checking and verifying E5092A settings.
Procedure to check the temperature control settings.
Measures DC voltage on control lines.
Verifies the settings for control lines.
Information on troubleshooting failed performance tests.
Instructions for ordering replacement parts.
Details the direct mail order system for parts within the USA.
A list of parts that can be replaced for the E5092A-020.
Illustrates the top view of major assemblies.
Top view of assemblies under the Switch Control USB PCA.
Illustrates the top view of the instrument's cables.
Top view of cables under the Switch Control USB PCA.
Top view of semirigid cables for SP4T configuration.
Top view of semirigid cables for SPDT configuration.
Top view of miscellaneous parts.
Top view of miscellaneous parts under the Switch Control USB PCA.
Bottom view of the instrument's cables.
Bottom view of semirigid cables for SP4T configuration.
Bottom view of semirigid cables for SPDT configuration.
Bottom view of miscellaneous parts.
Top view of the SP4T switch assembly.
Bottom view of the SP4T switch assembly.
Top view of the SPDT switch assembly.
Bottom view of the SPDT switch assembly.
Details the front panel components and their part numbers.
Details the rear panel components and their part numbers.
Details the side panel components and their part numbers.
Lists parts related to the LED assembly.
Lists other miscellaneous parts and documentation.
Outlines the general steps for replacing an assembly.
Lists the necessary tools for repair procedures.
Step-by-step guide for removing the outer cover.
Procedure for detaching the front chassis.
Steps for removing the front frame.
Procedure for removing the A1 Switch Control Board.
Steps for removing the power supply assembly.
Procedure for removing the power switch.
Steps for removing the main board.
Procedure for removing the SP4T switch assembly.
Steps for removing the SP4T Raptor Holder assembly.
Procedure for removing the SPDT switch drawer.
Procedure for removing the SPDT switch assembly.
Procedure for removing the switch indicator LED PCA.
Lists procedures to verify operation after assembly replacement.
Information on power supply and fuse specifications.
Details about the instrument's power cable and grounding.
Instructions for turning the instrument ON and OFF.
To Next Page
