Keysight PNA-X N5241A - Application Options

22 | Keysight | PNA Family Microwave Network Analyzers - Congurations Guide
PNA Family Network Analyzer Upgrade Kits (continued)
Application options
Upgrade kits are available to add options after initial purchase. To upgrade the PNA-X/PNA/PNA-L, order the corresponding
item number. The model and serial numbers of the instrument to be retrotted are required as part of the order.
1. For measuring frequency converters, Option 082 or 083 is required.
2. Requires congurable test set for signal conditioning of noise gure measurements using standard receivers. Therefore it is not available with N522xA-200, -210,
-400 and -410.
3. Upgrading N5244A units with noise gure hardware requires serial-number prexes of 5204 or higher, and upgrading N5245A units requires serial-number prexes of
5205 or higher. For these two models, units with lower serial-number prexes can be traded in for credit towards a new unit with the noise gure hardware.
4. Two-tone signal must be routed to R1 receiver after an external combiner; therefore it is not available with N522xA-200, -210, -400 and -410.
5. When used with an external signal generator, congurable test set is required to access a receiver. Therefore it is not available with N522xA-200 and -210.
6. To connect a multiport test set, congurable test set is required. Therefore it is not available with N522xA-200, -210, -400, -410, and N523xA-200, and -400.
7. The Windows 7 upgrade kit is model N8983A. This upgrade kit contains a new disk drive and requires an i7 or Celeron CPU. For units with older CPUs, order Option
PC6 for a new i7 CPU. When adding Option 090 on units with an older CPU, order Options PC6 and SP5.
8. A congurable test set is required for VMC measurements (to connect a reference mixer) or for SMC+Phase measurements using the comb-generator-based calibra-
tion. When ordered with N522xA-200, -210, -400 and -410, Option 083 adds phase and delay measurements only by using SMC+Phase with a calibration mixer.
9. Optional receiver attenuators are recommended to avoid receiver compression for large-scale measurements.
Description Required Option
For PNA-X
Series
For PNA
Series
For PNA-L
Series
User
Installable
Measurement applications
Automatic xture removal Windows 7 OS
7
. N524xAU-007 N522xAU-007 N523xAU-007 Yes
Time-domain measurements N524xAU-010 N522xAU-010 N523xAU-010 Yes
Noise gure measurements using standard receivers Option 080
1,2
N524xAU-028 N522xAU-028 n/a Yes
Fully-corrected noise gure measurements
for PNA-X, 2-ports
Option 080 and for N5241/42/49A, one of Op-
tions 219, 224 or H85
1
.
For N5244/45/47A, 080 and 224
N524xAU-924
3
n/a n/a No
Fully-corrected noise gure measurements
for PNA-X, 4-ports
Option 080 and for N5241/42/49A, one of Op-
tions 419, 423 or H85
1
.
For N5244/45/47A, 080 and 423
N524xAU-929
3
n/a n/a No
Frequency offset N524xAU-080 N522xAU-080 N523xAU-080 Yes
Scalar-calibrated converter measurements Option 080 N524xAU-082 N522xAU-082 N523xAU-082 Yes
Vector- and scalar-calibrated converter measurements Option 080
8
N524xAU-083 N522xAU-083 n/a Yes
Embedded LO measurements Option 082 or 083 N524xAU-084 N522xAU-084 n/a Yes
Gain compression application See Footnote 1 N524xAU-086 N522xAU-086 n/a Yes
Intermodulation distortion application Option 080
1,4
N524xAU-087 N522xAU-087 n/a Yes
Source phase control See Footnote 5 N524xAU-088 N522xAU-088 n/a Yes
Differential and I/Q devices application Option 080 and 400, 401, 410, 417, or 419, and
Windows 7 OS
7
N524xAU-089 N522xAU-089 n/a Yes
Spectrum analyzer Option 080, Windows 7 OS, and
DSP version 5
7, 9
N524xAU-090 N522xAU-090 n/a Yes
Integrated true-mode stimulus application Option 400, 401, 417, 419, or 423 N524xAU-460 N522xAU-460 n/a Yes
N-port capabilities See Footnote 6 N524xAU-551 N522xAU-551 N523xAU-551 Yes
Pulse, antenna, mm-wave
Pulsed-RF measurements Option 025
1
N524xAU-008 N522xAU-008 n/a Yes
Add IF inputs N524xAU-020 N522xAU-020 n/a Yes
Add pulse modulator to internal 1st source N524xAU-021 N522xAU-021 n/a Yes
Add pulse modulator to internal 2nd source Option 224, 400, 401, 417, 419, or 423 N524xAU-022 N522xAU-022 n/a Yes
Add four internal pulse generators N524xAU-025 N522xAU-025 n/a Yes
Fast CW sweep N524xAU-118 N522xAU-118 n/a Yes