KNEGT 504G3 Series - User Manual

Questions and Answers

A
Andres KennedyAug 30, 2025
Why is there increased noise in the bevel transmission of my KNEGT 504G3?
- G
  Grace VegaAug 31, 2025
  If you notice increased noise in the bevel transmission of your KNEGT Tractor, it could be due to several reasons. The bearing clearance of the small helical bevel might be too large, requiring adjustment. Abnormal gear engagement also necessitates adjustment. A differential shaft that is abraded and seized should be replaced. Additionally, abraded planetary gears or washers should be replaced, and a differential bearing that is abraded or damaged should also be replaced.
B
Brian Johnson DDSAug 29, 2025
Why does my KNEGT 504G3 steer wander during braking?
- C
  Cole PhillipsAug 29, 2025
  If your KNEGT Tractor is steering erratically during braking, it could be due to unequal free paths on the left and right brake pedals; adjust them to be equal. Another cause could be a damaged brake disk on one side, which would need replacing. Lastly, differing air pressures in the rear tires can cause this issue; check and inflate the tires according to specifications.
J
john07Aug 28, 2025
What to do if the clutch on my KNEGT 504G3 won't disengage?
- P
  pricerobertAug 28, 2025
  If your KNEGT Tractor's clutch cannot be fully separated, it could be due to several reasons. The pedal’s free path might be too large, and the working path too small, requiring adjustment of the pedal free travel. A driven disk that warps too much should be rectified or replaced. Also, the release fingers of the diaphragm spring not being on the same plane means replacement is needed.
J
Jonathon MilesAug 27, 2025
Why is my KNEGT 504G3 shivering at starting?
- C
  Carlos BrownAug 27, 2025
  If your KNEGT Tractor is shivering when starting, it could be due to contaminated friction and driven disks. Clean these disks to resolve the issue. Alternatively, a broken friction disk or a warped driven disk could also cause this problem, requiring replacement.
S
Shawn HarmonAug 27, 2025
What's causing the humming noise in my KNEGT 504G3 gearbox?
- J
  johnsondanielAug 27, 2025
  If there are unusual hum or slap noises coming from the gearbox of your KNEGT Tractor, it could be due to several reasons. The gear might be heavily abraded, have peeled tooth faces, or broken teeth, which would require replacing the gear. Alternatively, the bearing may be seriously abraded or damaged, necessitating bearing replacement. Improper clearance of bevel transmission could also be a factor, requiring adjustment. Lastly, insufficient lubricating oil or oil that doesn't meet the requirements could be the cause; fill the gearbox with enough of the correct lubricating oil.
J
Jasmine MendozaAug 25, 2025
Why is it so difficult to gear my KNEGT 504G3 Tractor?
- A
  Angel VincentAug 26, 2025
  If you're experiencing difficulties gearing or are unable to gear on your KNEGT Tractor, it may be because the clutch isn't separating completely. Refer to the clutch troubleshooting section for solutions. Another cause could be seriously abraded or damaged mesh sleeve end face and gear end face, which would need replacement or repair.
E
Emily JonesAug 25, 2025
Why are the front tires on my KNEGT Tractor wearing out so fast?
- D
  Danny McdonaldAug 25, 2025
  If your KNEGT Tractor's front tires are wearing out quickly, it could be due to several reasons. The front wheel rim or supporter may be seriously deformed, requiring correction. Improper front wheel toe-in adjustment could also be the cause, necessitating adjustment. Additionally, the steering knuckle and pins of the oil cylinder might be worn, requiring replacement. Finally, insufficient air pressure or front axle engagement during transport could be contributing factors; check and inflate the tires as needed and disconnect the front axle.