Why does my Kohler Marine Equipment emit black or gray smoke?
If your Kohler Marine Equipment generator emits black or gray smoke, check the oil level. Also check compression, as the issue might be worn piston rings or valves.
How to bleed the diesel fuel system in Kohler Inverter?
If there is air in the fuel system of your diesel Kohler Inverter, bleed the diesel fuel system to remove the air.
How to troubleshoot erratic operation of my Kohler 9-11EKOZD Marine Equipment?
If your Kohler Marine Equipment operates erratically, adjust the governor stability. Clean the cylinder head to address potential carbon buildup in the engine. Check cylinder pressures with a leakdown test and inspect the valves and valve seats to ensure the engine valves are seating correctly.
What to do if the customer connection fuse (F3) is blown in Kohler Inverter?
If the customer connection fuse (F3) is blown in your Kohler Inverter, replace the blown fuse. If the fuse blows again, check what is connected to the generator set.
What to do if the controller fuse (F2) is blown in Kohler Inverter?
If the controller fuse (F2) is blown in your Kohler Inverter, replace the blown fuse. If the fuse blows again, troubleshoot the controller.
What to do if there is a controller fault in Kohler Inverter?
If the controller of your Kohler Inverter has a fault, troubleshoot the controller.
What to do if my Kohler Marine Equipment starts but shuts down?
If your Kohler Marine Equipment generator starts but shuts down, check the controller’s display for a fault shutdown code. Correct the fault and then reset the controller.
Why my Kohler 9-11EKOZD cranks but does not start?
If your Kohler Marine Equipment generator cranks but does not start, begin by checking the fuel supply and fuel filters for any blockages. Inspect for loose or open connections at the fuel pump or fuel solenoid, and check the controller/engine wiring continuity. Ensure that the controller configuration settings are correct. Also, check for a locked rotor, which may be indicated by an overcrank fault shutdown.
What to do if my Kohler Marine Equipment generator set does not crank?
If your Kohler Marine Equipment generator set does not crank, there are several potential causes. It could be due to a weak or dead battery, in which case you should recharge or replace the battery. Check for reversed or poor battery connections. Inspect for loose connections or open circuits in the engine/controller connections, and verify the wire harness continuity. Replace the F2 fuse if it's blown; if it blows again, inspect the circuit and components, controller wiring, starter solenoid, and wiring for open grounds, loose connections, or pushed-out pins. Check the crank relay for 12VDC on lead 71N. Clean and retighten any poor ground connections. Inspect the starter and controller connections and operation, ensuring power to the controller.
What to do if Kohler Inverter shows low oil pressure shutdown?
If your Kohler Inverter experiences a low oil pressure shutdown, replace the low oil pressure switch. Also, check the engine for any potential damage.
General| Brand | Kohler |
|---|---|
| Model | 9-11EKOZD |
| Category | Marine Equipment |
| Language | English |
Specifies the generator sets are for marine applications.
Lists the generator set model numbers covered by the manual.
Area for recording specific generator set identification numbers.
Area for recording specific engine identification numbers.
Details hazards and preventative measures for accidental generator set starting.
Warns about fire risks related to fuel and engine operation.
Highlights the danger of carbon monoxide from exhaust systems.
Alerts to fire and explosion risks associated with fuel vapors.
Warns of potential hearing damage from generator noise.
Covers severe injury risks from electrical hazards and moving components.
Warns users about the danger of burns from hot engine components.
Offers contact information and resources for technical support and service.
Identifies specific parts required for maintenance and service.
Catalogues available literature such as manuals and spec sheets.
Diagram showing typical service points and components on the generator set.
Provides instructions for removing the sound shield roof for maintenance access.
Essential checks to perform before starting the generator set.
Recommends vessel and exhaust system inspections at the start of the boating season.
Specifies the limits for permissible angular operation of the generator.
Notes specific regulations and approvals for operation within the EU.
Advises on maintaining load profiles to prevent engine "wet stacking".
Explains the user interface and operation of the Advanced Digital Control.
Describes the function of the controller's display, buttons, and LED status indicator.
Step-by-step guide for starting the generator set, including safety notes.
Procedures for safely stopping the generator set.
Explains how the controller detects, displays, and responds to faults.
Describes the 12-character, 2-line alpha-numeric display for generator data.
Provides descriptions of system events, their types, and display messages.
Details the USB communication ports for PC and mass-storage devices.
Identifies the location and purpose of the generator set fuses.
Covers specifications for inhibit and time delays on fault shutdowns and warnings.
Lists fault shutdown and warning specifications with associated time delays.
Procedure for resetting the generator set controller after a fault shutdown.
Explains the internal voltage regulation function and calibration requirements.
Details adjustments for voltage regulator settings like voltage, frequency, and gain.
Describes warning conditions indicated by the system fault lamp and digital display.
Describes shutdown conditions indicated by the system fault lamp and digital display.
Explains status and notice messages displayed on the digital interface.
Introduces the menu structure and navigation for the controller's digital display.
Details methods for monitoring and programming the generator set controller via display or PC.
Explains how to communicate with the controller using USB and PC software.
Guides users on navigating and understanding controller menu data for monitoring and adjustments.
Lists potential error messages encountered during controller operations.
Displays basic generator set information and status, with auto-scrolling or fixed views.
Displays engine operating data such as speed, oil pressure, and coolant temperature.
Displays generator output voltage and frequency, with calibration procedures.
Shows factory-entered generator set and controller identification details.
Records total run time, number of starts, and energy generated.
Displays configurable system settings like frequency, battery voltage, and measurement units.
Details voltage regulator adjustment, volt/Hz, gain, and stability settings.
Allows review of up to 1000 stored system events, including faults and warnings.
Initiates the electric fuel pump to prime the fuel system.
Allows changing controller voltage settings, requiring output lead reconnection.
Illustrates the procedure for saving parameters and loading software via USB.
Covers general maintenance practices, safety warnings, and notices.
Provides a detailed service schedule based on operating intervals and models.
Details oil specifications, checking, and changing procedures for the lubrication system.
Covers fuel specifications, filter replacement, and system bleeding procedures.
Provides inspection points for the exhaust system, focusing on leaks and CO hazards.
Explains procedures for checking, filling, flushing, and cleaning the cooling system.
Details inspection and replacement procedures for the seawater pump impeller.
Explains the function and inspection of the siphon break system.
Describes the replacement procedure for the anticorrosion zinc anode.
Covers checking and adjusting belt tension for the seawater pump.
Refers to battery manufacturer's instructions for care and maintenance.
Provides a procedure for storing the generator set for extended periods.
Explains how fault codes displayed by the controller aid in troubleshooting.
Lists common controller-related troubleshooting symptoms and recommended actions.
Lists common cooling system troubleshooting symptoms and recommended actions.
Lists common engine troubleshooting symptoms and recommended actions.
Lists DC electrical system troubleshooting symptoms and recommended actions.
Lists common fuel system troubleshooting symptoms and recommended actions.
Lists common generator troubleshooting symptoms and recommended actions.
Lists common lubrication system troubleshooting symptoms and recommended actions.
Provides a reference to the point-to-point and schematic wiring diagrams.
Shows the point-to-point wiring diagram for the generator set.
Displays the schematic wiring diagram for the generator set.
Illustrates the point-to-point wiring for isolated ground units.
Provides the schematic wiring diagram for isolated ground units.
Details accessory interconnection wiring for various options.
Lists abbreviations used throughout the manual for clarity.
Provides a log for recording generator set operating hours and service dates.
Defines terms related to voltage regulator functions and adjustments.
Explains the function of underfrequency unloading for system response.
Describes how voltage reduction is determined during underfrequency conditions.
Defines the frequency threshold for initiating underfrequency unloading.
Explains how voltage regulators sense three-phase output.
Details specifications for adjusting voltage regulator settings.
Explains how to enter and adjust the desired generator set output voltage.
To Next Page
