EasyManua.ls Logo

Kohler GM87448

Kohler GM87448
24 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
18 TP-7077 3/19
Parameter Name
Battery Type
Range
Default Settings
Description
AGM 12 V
-40 – 0
-30
AGM 24 V
-80 – 0
-60
Gel 12 V
-40 – 0
-30
Gel 24 V
-80 – 0
-60
NiCad 12 V
-40 – 0
0
NiCad 24 V
-80 – 0
0
Output Enable
Active
Inactive
Active
Output Enable is always on and controlled
by the generator controller.
Forced Charge Cycle
Reset
Active
Inactive
Inactive
This feature allows a user to manually trigger
a refresh cycle where the charger goes into
the bulk cycle and cycles through the
charger cycle.
These is a single trigger of the feature. The
value returns to inactive automatically once
the action is triggered.
Default 12 V
13 – 15
14.25
Default 24 V
26 – 30
28.5
FLA 12 V
13 – 15
14.25
FLA 24 V
26 – 30
28.5
AGM 12 V
13 – 15
14.25
AGM 24 V
26 – 30
28.5
Gel 12 V
13 – 15
14.25
Gel 24 V
26 – 30
28.5
NiCad 12 V
13 – 16
14.5
Charger Voltage
Bulk (V)
NiCad 24 V
26 – 32
29
Target bulk voltage setpoint
Default 12 V
13 – 15
14.25
Default 24 V
26 – 30
28.5
FLA 12 V
13 – 15
14.25
FLA 24 V
26 – 30
28.5
AGM 12 V
13 – 15
14.25
AGM 24 V
26 – 30
28.5
Gel 12 V
13 – 15
14.25
Gel 24 V
26 – 30
28.5
NiCad 12 V
13 – 16
14.5
Charger Voltage
Absorption (V)
NiCad 24 V
26 – 32
29
Target absorption voltage setpoint
Default 12 V
13 – 14
13.25
Default 24 V
26 – 28
26.5
FLA 12 V
13 – 14
13.25
FLA 24 V
26 – 28
26.5
AGM 12 V
13 – 14
13.8
AGM 24 V
26 – 28
27.6
Gel 12 V
13 – 14
13.6
Gel 24 V
26 – 28
27.2
NiCad 12 V
12 – 16
14.5
Charger Voltage
Float (V)
NiCad 24 V
24 – 32
29
Target float voltage setpoint
Default 12 V
Not available
Not available
Default 24 V
Not available
Not available
FLA 12 V
14 – 16
15.5
FLA 24 V
28 – 32
31
AGM 12 V
Not available
Not available
AGM 24 V
Not available
Not available
Gel 12 V
Not available
Not available
Gel 24 V
Not available
Not available
NiCad 12 V
Not available
Not available
Charger Voltage
Equalize (V)
NiCad 24 V
Not available
Not available
Target equalize voltage setpoint.
Note: The controller’s high battery voltage
warning voltage shall set 0.2 V higher
then this value to avoid nuisance high
battery warnings while charger
performs the equalize cycle.

Related product manuals