-7-1411004 -T01-A
1. Make sure cold water supply line under the sink is
turned off; (Figure 1)
关闭原有的冷水供水阀并确认；(图1)
Connect the 1/4" plastic water tube to the water
filtration faucet. Refer to the installation guide on how
to install and connect the faucet.
将2分纯水塑料软管与净水龙头连接，龙头的安装及连
接方法见龙头安装说明书。
2. Disconnect cold water line from threaded stub on
bottom of tap faucet; (Figure 2)
将已连接的自来水龙头进水管螺纹端口从冷水供水
阀上拆开；(图2)
3. Screw in the female threaded stub of the water supply
adapter to the male threads of the cold water supply
valve as shown. Hand tighten and then tighten with
wrench until snug. Screw the female threaded tap
faucet stub to the water supply adapter; (Figure 3)
将三通转接内螺纹端口接到冷水供水阀外螺纹上，用活
动扳手拧紧；再将自来水龙头进水管内螺纹接头接到三
通转接外螺纹接口，用活动扳手拧紧；(图3)
Cold Water Supply Valve
冷水供水阀
Cold Water Supply Valve
冷水供水阀
Product water outlet
净水器纯水出口
1/4" Plastic Water Tubing Product
2分纯水塑料软管
Stub of Tap Faucet
自来水龙头进水端
Stub of Tap Faucet
自来水龙头进水端
Water Supply Adapter
三通转接
4. INSTALLATION 四、安装步骤
Step 1: Pre-install Water Filtration Faucet
(Refer to Figure 1- Figure 4)
Note: Please pre-install Kohler or other brand water filtration
faucet on the sink. (Refer to Water filtration Faucet Installation
Manual for tools and detailed installation steps of water
filtration faucet. For water filtration faucets other than Kohler
brand, please make sure the inlet dimension is G1/2" or with
a 1/4" adapter).
Applicable Kohler faucet models:
K-45406T-L-CP/K-76372T-4-CP
For non-Koller water filtration faucets, please make sure that
the water flow > 3.5 L/min at 100Kpa water pressure.
Note: When using a wrench to tighten the adapter, be
sure to do so softly. If excessive force is used, the
adapter may be damaged.
步骤一：选配净水龙头及接头安装（参见图 1 －图 4）
注意：请使用者确保在厨盆台面上安装固定好科勒牌或者自
行选配的净水龙头；（净水龙头安装所需工具及步骤请参照
净水龙头安装使用说明书，如非科勒牌的净水龙头，请确保
净水龙头连接口为标准 G1/2”口径接头或 2 分管快接接头。）
适配科勒龙头型号：K-45406T-L-CP/K-76372T-4-CP
非科勒牌净水龙头，请确保龙头在 100Kpa 水压下流量
＞3.5 升 / 分钟。
注意：用扳手拧紧接头时用力适当，如用力过猛，接头会
损坏。
Fig.1
图1
Fig.2
图2
Fig.3
图3
Fig.4
图4
To Next Page
Loading...
