4
3.4 Technical Data
Cutting System
-Enterprise for model TW/SW 100
- Unger for model TW/SW 98
Perforated disc diameter
- Model TW/SW 100
- Model TW/SW 98
Bowl capacity
- Standard bowl
- Large bowl
Worm speed
Size E32
Size B 98
100 mm
98 mm
45 litres
64 litres
200 rpm
Delivery rate
with 3 mm perforated disc
Motor rating/protection type
Motor speed
Motor voltage/three-phase current
Nominal current at 230/400 V
Fuse
Cable cross-section
Main dimensions
Table model TW 100
Floor model SW 100
Floor model SW 100H
Table model TW 98
Floor model SW 98
Floor model SW 98H
Table model TW 100
Floor model SW 100
Floor model SW 100H
Table model TW 98
Floor model SW 98
Floor model SW 98H
Filling height
depending on version
Height to underside of outfeed
Table model TW 98/100
Floor model SW 98/100
Floor Model SW 98/100H
Net/gross weight
Table model TW 100
Floor model SW 100
Floor model SW 100H
Table model TW 98
Floor model SW 98
Floor model SW 98H
approx.
1200 kg/h
2,9kW/IP54
1420 rpm
230/400 V
11,6/6,9 A
16A-slow action
1,5 mm²
L X W x H
with standard bowl
900 x540x 585 mm
900x540x1115 mm
900x540x1315 mm
950x540x 585 mm
950x540x1115 mm
950x540x1315 mm
with large bowl
1070x620x 585 mm
1070x620x1115mm
1070x620x1315mm
1120x620x 585mm
1120x620x1115mm
1120x620x1315mm
585 to 1315 mm
60 mm
600 mm
800 mm
97/117 kg
108/128 kg
110/130kg
100/120 kg
110/130 kg
113/133 kg
Every KOLBE product undergoes a thorough
acceptance test before being despatched where all of
the functions is checked.
4. Delivery of the Machine
The machine is supplied bolted to a wooden pallet and
shrink-packed in polyethylene protective foil. The machine
accessories, such as anti-vibration metal feet, support rollers,
combination hook wrench, splash guard, KOLBE mincer
feeding device, and the operating manual, are enclosed in a
carton (we only use reusable and recyclable packaging).
Please inform your supplier immediately if the contents of the
consignment do not agree with the pack list. In the event of
transport damage the forwarding company is to be notified
immediately and given an opportunity to inspect the damage.
5. Installation of the Machine
5.1 Installation Instructions
Undo the four securing screws and take the mincer off its
pallet. Accessories parts such as support and steering
rollers, anti-vibration metal feet, shafts, screws etc. are
packed in a separate carton.
Lift up the mincer safely using a fork lift or crane and remove
the wooden pallet.
Table model TW/SW 98/100
The table version of the mincer has 4 anti-vibration metal feet
(4) which should be screwed into the corners of the basic
frame.
Floor model SW 98/100 and SW 98/100 H
The stand version of the mincer has 2 support rollers (5)
which should be screwed into the two rear feet and 2 anti-
vibration metal feet (4) are to be screwed into the front feet.
In the case of the transportable version, steering rollers with
all stops are screwed in instead of the 2 anti-vibration metal
feet.
The anti-vibration metal feet can be raised or lowered over a
screw thread to compensate for unevenness in the floor.
The machine should be stored in a cooled or air-conditioned
room for hygiene reasons.
Apart from the floor space required for the machine one
should also provide an additional operating area of 1 x 1,5
metres at the front or on the side depending on which
operating side for the machine is chosen.
The machine must only be used in a room which is lit to an
intensity of at least 500 Lux.
All components which are to be regularly removed and
installed again weigh less than 20 kg. This removes the
necessity of having a transport equipment available at the
same height.
To Next Page
Loading...