user to carefully judge the situation beforehand to guarantee
adequate protection.
G) It is strictly forbidden to modify and/or repair the product: The
Manufacturer shall not be held liable for any damages, injuries or
death caused by: improper use, product modifications, repairs by
unauthorized persons or use of non-original spare parts
H) During transportation avoid exposure to U.V. radiations and
sources of heat and avoid contact with chemical reagents or
other corrosive substances, and adequately protect any pointed
or sharp parts. '+<8381never leave your equipment in a car
under the sun!
I) For the sake of your own safety, it is essential to make sure
that the product was sold to the public: complete, in their original
packaging and with the relative information. It is compulsory for
dealers selling products in countries other than the original des-
tination to check and supply the translation of this information.
L) This product has been tested and inspected piece by piece in
conformity with the Quality System certified to the UNI EN ISO
9001 international standard. Personal protective equipment is
certified by the notified body indicated in the relevant product
instructions. '+<83816+,9<+>9<C>/=>=38=:/->398=3809<7+
>398 +8.89<7= .9 89> +6A+C= 7+8+1/ >9 </:<9.?-/ A2+>
+->?+66C2+::/8=38:<+->3-/=9>2+>>2/:/<09<7+8-/=?8./<
</+6 -98.3>398= A2/8 ?=381 >2/ :<9.?-> 38 + 8+>?<+6 /8@3
<987/8>-+890>/8.300/<-98=3./<+,6C$2/,/=>3809<7+>398
-+8,/1+38/.,C-98>38?+6:<+->3-/?8./<>2/=?:/<@3=398
90=5366/.+8.;?+6303/.38=><?->9<=
_$#$"
Product maintenance consists of:
cleaning frequently wash the product with lukewarm (max.
40°C) drinking-water where necessary, you can also add some
gentle detergent. Rinse and leave to dry naturally away from
direct sources of heat, do not centrifuge.
disinfection (if necessary): soak the product for an hour in luke-
warm water adding disinfectant, then rinse again with drinking-
water, dry and lubricate. Avoid autoclave sterilization for textiles.
lubrication (for metallic products only): frequently lubricate the
mobile parts with silicone based oil. Avoid contact between oil
and textile parts. This job must be done after cleaning and com-
pletely drying.
Storage: after cleaning, drying and lubrication place the loose
equipment in a dry (40-90% relative humidity), fresh (tempera-
ture 5-40°C) and safe (avoid U.V. radiation) place, chemically
neutral (absolutely avoid salty environs), away from sharp
edges, sources of heat, dampness, corrosive substances or
other possible detrimental conditions. 989>=>9</A2/8A/>
_ "# $#
We would also strongly advise having pre and post use controls car-
ried out by qualified persons. Unless otherwise specified by stricter
provisions of law, it is recommended to have a competent person to
perform an accurate product inspection on an annual basis. Periodic
inspections results shall be recorded in the product control card. A
control card shall be provided for each component, subsystem and
system (please find a sample attached). Periodic inspections shall as
well check that product marks are clearly legible.
_ "%$
Read point 1C very carefully. Lifetime of metallic devices is the-
oretically unlimited while lifetime of textile or plastic devices is of
10 years from the production date under the following conditions:
maintenance and storage are made as described at point 2; pre
use, after use and periodic controls do not show any malfunction,
deformation, wear, etc., the device has been correctly used 89>
To Next Page
Loading...
