140
Phaser
Trml
(Tremolo)
Mt.Dly (Multitap Delay)
Reverb (Mono Reverb)
Gate
The Gate of 86:MM32: Reverb-Gate is connected to the Wet
output of the reverb.
This means that the on/off switch of the Gate effect is
linked to the Reverb, and will be switched on/off in con-
junction with the Reverb.
These algorithms can be selected as an insert effect if
“1in1outx8” is selected for “SelectEffType.”
Different insert effects can be used on each of eight channels/
tracks.
Effects MN1–MN11 are monaural type effects.
“1in1outx8” effects cannot be controlled by an expression
pedal etc.
88: MN1: OverDrive/HighGain
The parameters are the same as for ODHIG.
89: MN2: Compressor2
The parameters are the same as for Comp2.
90: MN3: Limiter
The parameters are the same as for Lmtr.
91: MN4: Gate
92: MN5: Exciter2
The parameters are the same as for Excit2.
93: MN6: Parametric 4band EQ
94: MN7: Amp Simulator
95: MN8: Multitap Delay
The parameters are the same as for Mt.Dly.
96: MN9: Chorus/Flanger2
The parameters are the same as for ChFl2.
97: MN10: Phaser
The parameters are the same as for Phaser.
LFO (LFO Waveform)....................... TRI, SIN Selects LFO Waveform
*Speed (LFO Frequency [Hz]) ....0.02...20.0Hz Sets the LFO speed
Manual (Manual)................................. 0...100 Sets the frequency to which the effect is
applied
*Depth (Depth)...................................... 0...100 Sets the depth of LFO modulation
Reso (Resonance)...................... –100...+100 Sets the resonance amount
Mix (Wet/Dry).....................–Wet...–1:99, Dry,
1:99...Wet
Sets the phaser effect balance
LFO (LFO Waveform)...................... TRI, SIN,
Vintage, Up, Down
Selects LFO Waveform
Shape (LFO Shape).................... –100...+100 Determines how much the LFO wave-
form is changed
*Speed (LFO Frequency [Hz]) ....0.02...20.0Hz Sets the LFO speed
*Depth (Depth)...................................... 0...100 Sets the depth of LFO modulation
T1Time (Tap1 Time [msec]) ........... 0...680ms Sets the Tap1 delay time
T2Time (Tap2 Time [msec]) ........... 0...680ms Sets the Tap2 delay time
T1Lvl (Tap1 Level)............................... 0...100 Sets the Tap1 output level
Fdback (Feedback) ..................... –100...+100 Sets the Tap2 feedback amount
HiDamp (High Damp [%]) ................... 0...100 Sets the damping amount in the high
range
Mix (Wet/Dry).................Dry, 1:99...99:1, Wet Sets the effect balance of the multi-tap
delay
Time (Reverb Time [sec])...........0.1...10.0sec Sets the reverberation time
HiDamp (High Damp [%]) ................ 0...100% Sets the damping amount in the high
range
PreDly (Pre Delay [msec]) ..........0...200msec Sets the delay time of the reverb sound
and gate control signal
EQTrim (EQ Trim)................................ 0...100 Sets the EQ input level
LEQG (Pre LEQ Gain [dB]).........–15...+15dB Sets the gain of Low EQ
HEQG (Pre HEQ Gain [dB])........–15...+15dB Sets the gain of High EQ
RevBal (Reverb Balance)...... Dry, 1:99...99:1,
Wet
Sets the effect balance of the reverb
Contrl (Input Reverb Mix)......Dry, 1:99...99:1,
Wet
Sets the balance between the dry and
reverb sounds of the gate control signal
Polrty (Polarity) ........................................ +, – Switches between non-reversed and
reversed Gate on/off
Thrshl (Threshold)............................... 0...100 Sets the level to which the Gate is
applied
Attack (Attack)..................................... 1...100 Sets the attack time
Relse (Release) .................................. 1...100 Sets the release time
Insert (1in1outx8)
Polrty ([G] Polarity) ...................................+, – Switches between non-reversed and
reversed Gate on/off
Thrshl (Threshold) ...............................0...100 Sets the level to which the Gate is
applied
Attack ([G] Attack) ...............................1...100 Sets the attack time
Relse (Release)...................................1...100 Sets the release time
Fc1 (Band1 Cutoff [Hz])........... 20Hz...1.0kHz Sets the center frequency of Band 1
Q1 (Q) .............................................0.5...10.0 Sets the bandwidth of Band 1
G1 (Gain [dB]) ............................ –18...+18dB Sets the gain of Band 1
Fc2 (Band2 Cutoff [Hz])....... 300Hz...10.0kHz Sets the center frequency of Band 2
Q2 (Q) .............................................0.5...10.0 Sets the bandwidth of Band 2
G2 (Gain [dB]) ............................ –18...+18dB Sets the gain of Band 2
Fc3 (Band3 Cutoff [Hz])....... 300Hz...10.0kHz Sets the center frequency of Band 3
Q3 (Q) .............................................0.5...10.0 Sets the bandwidth of Band 3
G3 (Gain [dB]) ............................ –18...+18dB Sets the gain of Band 3
Fc4 (Band4 Cutoff [Hz])....... 500Hz...20.0kHz Sets the center frequency of Band 4
Q4 (Q) .............................................0.5...10.0 Sets the bandwidth of Band 4
G4 (Gain [dB]) ............................ –18...+18dB Sets the gain of Band 4
Tr im (Trim) ...........................................0...100 Sets the parametric EQ input level
Type (Amplifier Type) ....................... AMP1...5 Selects the type of guitar amplifier
To Next Page
Loading...
