Korg SP-280 - Program and Control Change Filtering

21
Enabling/disabling control change transmission/
reception ltering
Messages, such as operation of the SP-280’s damper pedal,
can be transmied to a connected external MIDI device to
control it, and these messages can be received from the ex-
ternal MIDI device to control the SP-280.
To transmit/receive control change messages, disable this
function (oFF: default seing). To not transmit/receive the
messages, enable this function (on).
• EntertheMIDIfunctionmode,andthenpressthe
E.PIANO2buon.
The LED for the E.PIANO2 sound buon lights up, and
the seing (oFF) appears in the display.
Using the SP-280 as a multi-timbral sound module
The SP-280 can operate as a 16-part multi-timbral sound
module when an external MIDI device is used to control
its internal sound generator.
1. ConnectaMIDIcabletotheSP-280’sMIDIINcon-
nectorandtotheMIDIOUTconnectorofasequencer
orotherMIDIdevice.
2. TransmitMIDIdatafromtheconnectedsequenceror
otherMIDIdevice.
For details on transmitting data from the connected
sequencer or other MIDI device, refer to its user’s man-
ual.
3. WhentheSP-280receivestheprogramchangemes-
sagealongwiththeperformancedata,itwillplay
withthesoundcorrespondingtothatprogramnum-
ber.
If the SP-280 is not to be used as a multi-timbral sound
module, disable this function (oFF).
• EntertheMIDIfunctionmode,andthenpressthe
HARPSI/CLAVbuon.
The LED for the HARPSI/CLAV sound buon lights up,
and the seing (on: default seing) appears in the dis-
play.
Enabling/disabling program change transmis-
sion/reception ltering
The programs on a connected MIDI device can be changed
by sending a MIDI change number from the SP-280. In
addition, the programs on the SP-280 can be changed by
receiving a MIDI change number from a connected MIDI
device.
For program change numbers and their corresponding
sounds, refer to “Table of sounds and corresponding pro-
gram change numbers” below.
To transmit/receive program change messages, disable this
function (oFF: default seing). To not transmit/receive the
messages, enable this function (on).
• EntertheMIDIfunctionmode,andthenpressthe
E.PIANO1buon.
The LED for the E.PIANO1 sound buon lights up, and
the seing (oFF) appears in the display.
Transmiingprogramchanges
When a sound is selected using the sound buttons and
BANK buon on the SP-280, the corresponding MIDI pro-
gram change number is transmied.
Receivingprogramchanges
When the SP-280 receives a MIDI program change number,
the sound is changed to the corresponding one.
If an incompatible program change number is re-
ceived, the SP-280 sound is not changed.
Tableofsoundsandcorrespondingprogramchange
numbers
CC0: Bank Select (MSB) for all sounds is set to 121.
SoundBuon Bank CC32 PC Sound
PIANO1 1 0 0
Grand Piano
2 1 0
Classic Piano
3 0 1
Jazz Piano
PIANO2 1 2 0
Live Piano
2 0 3
Honky-Tonk
3 0 2
Elec.Grand
E.PIANO1 1 0 4
Club E.piano
2 1 4
Vintage E.Piano
3 3 4
Tremoro EP
E.PIANO2 1 0 5
Dig.E.Piano1
2 2 4
60's E.Piano
3 1 5
Dig.E.Piano2
HARPSI/CLAV 1 0 6
Harpsichord
2 0 7
Clav
3 1 7
Synth Clav
VIBES/
GUITAR
1 0 11
Vibraphone
2 0 12
Marimba
3 0 24
Acoustic Guitar
ORGAN1 1 0 16
Jazz Organ1
2 1 16
Jazz Organ2
3 0 17
Jazz Organ3
ORGAN2 1 0 19
Pipe Organ1
2 1 19
Pipe Organ2
3 2 19
Positive Organ
STRINGS 1 0 48
Strings
2 0 50
Cinema Strings
3 1 50
Analog Strings
CHOIR 1 0 52
Aah Choir
2 1 52
Ooh Voices
3 2 52
Classical Choir