54
Save Template Song (Save as User Template Song)
This command saves the program selections, track parame-
ters, and effect settings etc. of the song as a user template
song U00–15.
1 Select “Save Template Song” to access the dialog box.
2 In “To,” specify the user template song (U00–15) in which
the data will be saved.
3 To save the template song, press the [F8] (“OK”) key. To
cancel, press the [F7] (“Cancel”) key.
Be aware that when you execute this command, all set-
ting data of the save destination User Template Song will
be erased and rewritten.
FF/REW Speed
This allows you to set the speed at which fast-forward or
rewind will occur when you press the [FF] key or [REW]
key.
1 Select “FF/REW Speed” to access the dialog box.
2 In “Speed,” specify the speed (relative to the playback
tempo) at which fast-forward and rewind will occur.
With a setting of 2, this will occur at double the playback
tempo; with a setting of 3, triple the tempo; and with a
setting of 4, quadruple the tempo. However in sections
where the playback data is dense, the fast-forward or
rewind speed may slow down.
3 If “Ignore Tempo” is checked, the playback tempo and
note length will be ignored, and fast-forward and rewind
will be performed as fast as possible. The speed of fast-
forward and rewind will differ between sections where
the playback data is dense and sections where it is sparse.
If this item is unchecked, fast-forward and rewind will
be performed at the speed you specify for “Speed.”
4 To execute the settings, press the [F8] (“OK”) key. To can-
cel, press the [F7] (“Cancel”) key.
Set Location (Set Location for Locate Key)
When you press the [LOCATE] key, you will move to the
location specified here.
1 Select “Set Location” to access the dialog box.
2 In “Location,” specify the location to which you will
move when you press the [LOCATE] key. If you specify
001:01:000, you will move to the beginning of the song
when you press the [LOCATE] key.
3 To execute the settings, press the [F8] (“OK”) key. To can-
cel, press the [F7] (“Cancel”) key.
Even when this dialog box is not opened, you can set
this value to the current location by holding down the
[ENTER] key and pressing the [LOCATE] key.
GM Initialize
This command transmits a GM System On message to
Sequencer mode, resetting all tracks to the GM settings
(refer to the table below).
In Sequencer mode when a GM System On message is
received from an external device or the tone generator
will be reset to the GM settings in the same way as
when this command is executed (However even in
these cases, the parameters of the 7.2: Master Fx will not
be reset).
GM Initialize Parameters
Parameter Track1–9, 11–16 Track10
1.1 Program Select G001:Acoustic Piano g001: (d): STANDARD Kit
Pan C064 C064
Volume 100 100
3.1 Status – – The setting remains unchanged
3.2 Use Program’s Scale – – The setting remains unchanged
6.1 Arpeggiator Assign – – The setting remains unchanged
Other Arpeggiator parameters – – The setting remains unchanged
7.1 IFX/Indiv.Out BUS Select L/R DKit
Send1(MFX1) 0 0
Send2(MFX2) 40 40
IFX – – The setting remains unchanged
Pan(CC#8) – – The setting remains unchanged
BUS Select – – The setting remains unchanged
Send1 – – The setting remains unchanged
Send2 – – The setting remains unchanged
Other Insert Effect parameters – – The setting remains unchanged
7.2 MFX1 – – 16: St. Chorus
MFX2 – – 53: Rev Smth. Hall
Return1 – – 127
Return2 – – 050
Other Master Effect and Master EQ parameters – – Default settings
To Next Page
Loading...
