TRITON STUDIO Easy Start
7
…Continue by sampling through one of the TRITON STUDIO’s 102 Insert effects:
11. Press the Input Setup tab
Ä In the Input 1 field, press the X popup by BUS(IFX) Select and choose IFX1.
12. Press the[MENU] key, and then press P8: Insert Efffect.
Ä Press the OFF toggle button in the IFX1 box to turn it ON,
and then make sure that 000: “No Effect” is highlighted.
Ä Use the numeric keypad to enter 5 > 2, and then press the
[ENTER] key (“52: Reverb Hall”)
Ä Speak into the microphone to hear the effect being applied Ä Press the IFX1 tab at
the bottom of the screen to view and edit the effect parameters.
13. Press the [MENU] key, then press P0: Recording
Ä Press theRecording tab, then press the SAMPLING [REC/WRITE]
key to “arm” the sampler
Ä Speak into the mic and adjust the recording level as needed.
14. Press Create to make a new index in the multisample
Ä Press the SAMPLING [START/STOP] key, speak to sample Ä
Press SAMPLING [START/STOP] again to stop sampling. The new sample will playback on key [E2] – the next
available index.
New!! Sampling in Program, Combi, or Sequence modes
The TRITON STUDIO easily allows sampling in Program, Combi or Sequence Mode. Note that there is a Sampling tab
on the main play page of each mode. The following Combi example illustrates the procedure for all three modes:
1. Press the [Combi] key and select A032, “SKOOL of FUNK”: The objective is to sample all this information,(up to 8
Timbres, 7 Effects, and 2 polyphonic Arps) as a single new event, freeing up tracks and polyphony in sequencing.
2. Press the Sampling tab at the bottom of the display
Ä Make sure that the Input X popup is set to Analog Ä Press the
SAMPLING [REC] key and adjust the level as in step 5 above
Ä When finished, press the SAMPLING [REC] key again
Ä Turn OFF the ARPEGGIATOR [ON/OFF] key.
3. In the Sampling Setup field set Source BUS to L/R
Ä Set Trigger to Note On Ä Set Save to to RAM Ä Set Mode to
Stereo.
4. Press the upper right corner ▼ popup and press Select Bank & Sample No.
Ä Check the box in reply to Convert to
Program and select a Program destination
Ä Press the X popup by MS and select the next empty Multisample slot
(MS001 assuming that you’ve performed the previous “One-shot” tutorial): Orig. Key will then default to C2
Ä Press OK.
5. Turn on the ARP [ON/OFF] switch
Ä Press the SAMPLING [REC] key Ä Press the SAMPLING [START/STOP] key Ä
Play the keyboard Ä When finished, turn off the SAMPLING [REC] and ARP [ON/OFF] keys.
6. Press the [PROG] key and select the Program you selected in step 4: Play [C2] and hear your entire phrase as one
sample!
Tip! Try the previous exercise using another “realtime controllable” Combination like C095 Radio Ribbonizer – but this time,
as you sample, work with the REALTIME CONTROLS, RIBBON, JOYSTICK and ARPEGGIATOR CONTROLS – all
your controller movements are recorded in your new sample, available for use as a single MIDI event in your sequences!
New!! In-Track Sampling in Sequence mode
TRITON STUDIO allows an external audio input (a guitar or mic for example) to easily be sampled and assigned a
trigger note to an empty sequence track in order to play back at the correct location. The following example shows the
procedure utilizing the mic you’ve previously connected to Audio Input 1.
1. Clear the Sample RAM, but not your Sequences: To do this, press the [SAMPLING] mode key, press the upper right
corner ▼ popup and press Delete MS
Ä Check both boxes All Multisamples and Delete samples Too? Ä Press OK
2. Press the [SEQUENCE] mode key and select one of the songs you created from the steps above.
Ä Press the Sampling
tab in the display.
To Next Page
Loading...
Need help?
General
