EasyManua.ls Logo

kozy heat 936 - User Manual

kozy heat 936
39 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Report No. 216-F-24-4
www.kozyheat.com
MAY 2012
936-REV-23
DIRECT VENT GAS FIREPLACE
INSTALLATION AND OPERATION MANUAL
—Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
◙ Do not try to light any appliance.
◙ Do not touch any electrical switch: do not use any phone in your building.
◙ Immediately call gas supplier from a neighbors phone. Follow the gas
supplier instructions.
◙ If you cannot reach your gas supplier, call the fire department.
— Installation and service must be performed by a qualified installer, service
agency or the gas supplier.
WARNING: If the information in these instructions is not followed exactly, a fire
or explosion may result causing property damage, personal injury or loss of life.
WARNING
This appliance may be installed in an aftermarket permanently located,
manufactured home (USA only) or mobile home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This
appliance is not convertible for use with other gases, unless a certified kit is used.
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

Table of Contents

Other manuals for kozy heat 936

Preview: Installation & Operating Manual
Installation & Operating Manual35 pages
Preview: Installation And Operating Manual
Installation And Operating Manual31 pages

Questions and Answers

  • M
    Matthew CarrollAug 8, 2025
    What to do if my kozy heat 936 burner won't light?
    • B
      Brian SmithAug 8, 2025
      If the burner on your Kozy Heat Indoor Fireplace won't light, several factors could be the cause. First, ensure the pilot light is lit. Next, check that the regulator valve is turned "on." Also, verify the rocker switch is activated, exposing the "Red" or "on" indicator. If these steps don't work, inspect the rocker switch wire connections and the generator wires at the regulator terminals for looseness. Additionally, check for pinched generator wires. Finally, ensure that any connected wall switch, remote control, or thermostat is properly connected and set.
  • S
    Shaun LiuAug 12, 2025
    Why won't my kozy heat 936 pilot stay lit?
    • N
      Nicole EvansAug 12, 2025
      If the pilot light on your Kozy Heat Indoor Fireplace won't stay lit, consider these potential causes: * Ensure you are holding the black control knob in long enough to properly heat the thermocouple. * Check the thermocouple wire connection at the valve to make sure it is secure. * Examine the pilot hood to confirm it's not misdirecting the pilot flame away from the thermocouple; the flame must burn on both the generator and thermocouple.
  • J
    Jamie SanchezAug 15, 2025
    Why won't my Kozy Heat Indoor Fireplace pilot light?
    • B
      Brandon WilliamsAug 16, 2025
      If the pilot light on your Kozy Heat Indoor Fireplace won't light, check the following: First, ensure the gas supply is turned on. Next, make sure the gas line has been bled out by holding the black control knob in long enough. Finally, verify that you are holding the black control knob in long enough.
  • J
    julie01Aug 20, 2025
    What to do if my kozy heat 936 burner won't stay lit?
    • K
      Katherine CaldwellAug 20, 2025
      If the burner on your Kozy Heat Indoor Fireplace won't stay lit, the issue might be related to the wall switch or thermostat wiring. If a wall switch or thermostat is connected with wire that is too thick or runs more than 30 ft, disconnect the wires from the valve. If the burner then stays lit, you should change the location or use the on/off switch only.
  • A
    Anthony BakerAug 25, 2025
    How to fix no spark when piezo button is depressed on Kozy Heat Indoor Fireplace?
    • W
      William Hendricks MDAug 25, 2025
      If there's no spark when you press the piezo button on your Kozy Heat Indoor Fireplace, try these solutions: First, tighten the nut that holds the piezo in place. Next, ensure the wire on the back of the piezo button is securely connected. Also, check that the wire from the piezo to the electrode is firmly connected at the electrode. Finally, realign the electrode, ensuring there's a 1/8" space between it and the pilot.
  • J
    John JonesAug 29, 2025
    Why are the flames lifting on my Kozy Heat Indoor Fireplace?
    • A
      Ashley CooleyAug 29, 2025
      If the flames on your Kozy Heat Indoor Fireplace are lifting or ghosting, it's likely due to insufficient draft caused by too much restriction. To resolve this, remove the inner ring(s) on the restrictor or remove the restrictor completely.
  • B
    blackburnhenrySep 2, 2025
    How to fix short, flickering flames on kozy heat 936 Indoor Fireplace?
    • J
      James RodriguezSep 2, 2025
      If your Kozy Heat Indoor Fireplace has short, flickering flames, it's likely due to excessive draft caused by not enough restriction. A simple solution is to add a restrictor.

kozy heat 936 Specifications

General IconGeneral
Model936
CategoryIndoor Fireplace
Log Set MaterialCeramic Fiber
Fuel TypeNatural Gas or Liquid Propane
Efficiency70%

Related product manuals