Kramer VW-9 - Page 47

Kramer Electronics Ltd.
VW-9 – Protocol 3000
45
Function
Description
Syntax
Parameters/Attributes
Example
HDCP-STAT?
Get HDCP signal status.
io_mode =1 – get the
HDCP signal status of the
sink device connected to
the specified output.
io_mode =0 – get the
HDCP signal status of the
source device connected
to the specified input.
COMMAND
#HDCP-STAT?io_mode,in_index<CR>
FEEDBACK
~nn@HDCP-STATio_mode,in_index,status<CR><LF>
io_mode – Input/Output
0 – Input
1 – Output
io_index – Number that indicates the
specific number of inputs or outputs (based
on io_mode):
for inputs:
1 – Input 1
2 – Input 2
3 – Input 3
4 – Input 4
For outputs:
1 – Output 1
2 –Output 2
3 – Output 3
4 – Output 4
5– Output 5
6 – Output 6
7 – Output 7
8 – Output 8
9 – Output 9
10 – Output 10
status – Signal encryption status - valid
values On/Off
0 – HDCP Off
1 – HDCP On
Get the output HDCP-
STATUS of IN 1:
#HDCP-
STAT?0,1<CR>
HELP
Get command list or help
for specific command.
COMMAND
#HELP<CR>
#HELPcmd_name<CR>
FEEDBACK
1. Multi-line:
~nn@Devicecmd_name,cmd_name…<CR><LF>
To get help for command use: HELP
(COMMAND_NAME)<CR><LF>
~nn@HELPcmd_name:<CR><LF>
description<CR><LF>
USAGE:usage<CR><LF>
cmd_name – Name of a specific command
Get the command list:
#HELP<CR>
To get help for
AV-SW-TIMEOUT:
#HELPav-sw-timeou
t<CR>
IDV
Set visual indication from
device.
Using this command,
some devices can light a
sequence of buttons or
LEDs to allow
identification of a specific
device from similar
devices.
COMMAND
#IDV<CR>
FEEDBACK
~nn@IDVok<CR><LF>
#IDV<CR>
IMAGE-PROP
Set the image size.
Sets the image
properties of the selected
scaler.
COMMAND
#IMAGE-PROPscaler_id<CR>
FEEDBACK
~nn@IMAGE-PROPscaler_id,video_mode…<CR><LF>
scaler_id – Scaler number –
* – All
video_mode – Status
1 – Full
2 – Best fit
3 – Follow input
Set the image size:
#IMAGE-PROP*<CR>
IMAGE-PROP?
Get the image size.
Gets the image
properties of the selected
scaler.
COMMAND
#IMAGE-PROP?scaler_id<CR>
FEEDBACK
~nn@IMAGE-PROPscaler_id,video_mode…<CR><LF>
scaler_id – Scaler number –
* – All
video_mode – Status
1 – Full
2 – Best fit
3 – Follow input
Get the image size:
#IMAGE-PROP?*<CR>
INFO-IO?
LEGACY COMMAND.
Get in/out count.
COMMAND
#INFO-IO?<CR>
FEEDBACK
~nn@INFO-IOININinputs_count,OUToutputs_count
<CR><LF>
inputs_count – Number of inputs in the
unit
outputs_count – Number of outputs in
the unit
Get inputs count:
#INFO-IO?<CR>
INFO-PRST?
LEGACY COMMAND.
Get maximum preset
count.
In most units, video
and audio presets with the
same number are stored
and recalled together by
commands #PRST-STO
and #PRST-RCL.
COMMAND
#INFO-PRST?<CR>
FEEDBACK
~nn@INFO-PRSTVIDpreset_video_count,AUDpreset_
audio_count<CR><LF>
video_preset_count – Maximum
number of video presets in the unit
audio_preset_count – Maximum
number of audio presets in the unit
Get number of video and
audio presets:
#INFO-PRST?<CR>
LOCK-FP
Lock the front panel.
COMMAND
#LOCK-FPlock/unlock<CR>
FEEDBACK
~nn@LOCK-FPlock/unlock<CR><LF>
lock/unlock – On/Off
0 – Off unlocks front panel buttons or
keyboard
1 – On locks front panel buttons or
keyboard
Unlock front panel:
#LOCK-FP0<CR>
LOCK-FP?
Get the front panel lock
state.
COMMAND
#LOCK-FP?<CR>
FEEDBACK
~nn@LOCK-FPlock/unlock<CR><LF>
lock/unlock – On/Off
0 – Off unlocks front panel buttons or
keyboard
1 – On locks front panel buttons or
keyboard
Get the front panel lock
state:
#LOCK-FP?<CR>