Safety
15
Pos: 16.12 /BA/Sic herheit/Hydr aulikanlage @ 2\mod_12035 03691986_78.d ocx @ 66225 @ 2 @ 1
3.7 Hydraulic system
1 The hydraulic system is pressurised!
2 When connecting hydraulic cylinders and motors, make sure the hydraulic hoses are
connected as specified!
3 When connecting the hydraulic hoses to the tractor hydraulics, make sure that the
hydraulics of both the tractor and the implement have been depressurized!
4 In the case of hydraulic connections between tractor and machine, the coupling sleeves and
plugs should be marked to ensure a proper connection! If the connectors are interchanged,
the function will be reversed (e. g. raising/lowering) - Risk of accident!
5 When searching for leaks, use suitable aids to avoid the risk of injury!
6 Liquids escaping under high pressure (hydraulic oil) can penetrate the skin and cause
serious injury! Seek medical help immediately should injuries occur! Danger of infection!
7 Before working on the hydraulic system, depressurise the system and switch off the engine!
Pos: 16.13 /BA/Sic herheit/Hydr aulikanlage Zus atz Alterung der H ydraulikschl auchleitungen @ 3\mod_12 04552944856 _78.docx @ 70772 @ @ 1
8 Check the hydraulic hose lines at regular intervals and replace them if damaged or worn!
The new hoses must fulfill the technical requirements set by the manufacturer of the
implement!
Pos: 16.14 /Übersc hriften/Überschrif ten 2/U-Z/ WWartung @ 3 3\mod_125422 2340957_78.d ocx @ 318599 @ 2 @ 1
3.8 Maintenance
Pos: 16.15 /BA/Sic herheit/Wart ung/Wartung Pos .1 ohne Sch wungmass/Feststell bremse anzie hen (2013- 12-18 09:48:30) @ 17\ mod_1236239 576347_78.doc x @ 203270 @ @ 1
1 Always make certain that the drive and the engine are switched off before doing any
repairs, maintenance or cleaning! - Remove the ignition key!
Pos: 16.16 /BA/Sic herheit/Wart ung/Wartung Pos .2 bis 8 ohne Ele ktronik @ 73 \mod_1308 295728779_7 8.docx @ 655465 @ @ 1
2 Regularly check that nuts and bolts are properly seated and tighten if necessary!
3 When performing maintenance work with the machine raised, always secure it with suitable
supporting elements!
4 Oils, greases and filters must be disposed of correctly!
5 If protective devices and guards are subject to wear, check them regularly and replace them
in good time!
6 Replacement parts must at least comply with the technical requirements set by the
manufacturer of the implements! This is guaranteed by original KRONE spare parts!
Pos: 16.17 /BA/Sic herheit/Wart ung/Wartung Z usatz Schneidwe kzeuge @ 12 \mod_1224 578273531_78. docx @ 151591 @ @ 1
7 When replacing working tools with cutting edges, use suitable tools and gloves!
Pos: 16.18 /BA/Sic herheit/Eige nmächtiger Umb au und Ersatzteil herstellung @ 1\mod_12 01937705539_78. docx @ 557 45 @ 2 @ 1
3.9 Unauthorised Conversion/Modification and Spare Parts Production
Conversions or modifications of the machine are permitted only with prior consultation with the
manufacturer. Original spare parts and accessories authorised by the manufacturer help to
ensure safety. Use of other parts may void liability for resulting damage.
Pos: 16.19 /BA/Sic herheit/Unzuläs sige Betriebs weisen @ 11\ mod_12233576 99923_78.doc x @ 145527 @ 2 @ 1
3.10 Inadmissible Modes of Operation
The operating safety of the delivered machine is guaranteed only when it is used as intended in
compliance with the introductory section "Intended use" of the operating instructions. The limit
values listed in the data charts should not be exceeded under any circumstances.
Pos: 17 /Layout M odule /---------------Seitenumbruch---------------- @ 0\m od_119617531 1226_0.docx @ 4 165 @ @ 1
To Next Page
Loading...
