KUHN VBP 2190 User Manual (English)

Questions and Answers:

M
melissa58Sep 3, 2025
What to do if the satellite is not in zero position on KUHN VBP 2190?
- A
  Amy Walker DDSSep 3, 2025
  If the satellite is not in zero position, check the satellite area for blockage and remove it. Check the working of the hydraulic circuit (leakage / filter) and that there is enough oil flow. If the hydraulic oil flow is too high, adjust or calibrate the hydraulic oil flow. If there is no electric power from PCB to the hydraulic block, contact your dealer. If the satellite rpm sensor and/or satellite zero position sensor faulty or adjusted incorrectly, adjust the sensors, check the working and replace if necessary.
E
Edwin CrawfordSep 2, 2025
What to do if the table is not in unload position within the time limit on KUHN VBP 2190?
- M
  Megan MezaSep 2, 2025
  If the table is not in the unload position within the time limit, check the working of the hydraulic circuit for leakage or filter issues to ensure there is enough oil flow. Inspect for any pollution or mechanical obstruction near the wrapping table and remove it. If there is no electric power from PCB to the hydraulic block, contact your dealer. If the table angle sensor is incorrect adjusted or faulty, readjust the sensors, check the workings and replace if necessary.
S
Seth JenkinsAug 23, 2025
What to do if there is no message at the KUHN VBP 2190 Farm Equipment electronic control box?
- M
  Michael ConleyAug 25, 2025
  If there is no message at the electronic control box, first switch on the electronic control box. Then check if the electronic control box is connected to the 12V supply at the tractor. Inspect all electrical wiring and check the fuses. If a fuse is melted, determine what caused it before replacing it, and solve that underlying issue first. If the problem is internal, contact your dealer.
B
Briana MejiaSep 1, 2025
Why is the sensor and micro controller power below the minimum on my KUHN VBP 2190?
- A
  anelsonSep 1, 2025
  If the sensor and micro controller power is below the minimum, it could be because the terminal is activated while starting the tractor, so switch off the terminal, ensure the tractor engine is running, and then switch on the terminal. The tractor voltage might be too low, so reduce the electric power consumption at the tractor. There might be bad electrical connections, so check the connections and wiring of the 12 V out (2.5 mm2 wire). The fuse in the machine box or in the power cable of the ECU could be blown, so disconnect all outputs, replace the fuse, and reconnect them one by one to find the problem.
J
James EvansAug 31, 2025
What to do if loading arm 2 is not in the upper position within the time-out on KUHN VBP 2190?
- J
  Jared DaltonAug 31, 2025
  If loading arm 2 is not in the upper position within the time-out, check the working of the hydraulic circuit for leakage or filter issues to ensure there is enough oil flow. Inspect for any mechanical obstruction at loading arm 2 and remove it. If there is no electric power from PCB to the hydraulic block, contact your dealer. If the Loading 2 arm up sensor is faulty or adjusted incorrectly, adjust the sensor, check its working, and replace it if necessary.
N
Natalie BaileyAug 30, 2025
What to do if the tailgate is not closed when the satellite moves on KUHN VBP 2190 Farm Equipment?
- R
  Rodney MccannAug 30, 2025
  If the tailgate is not closed when the satellite moves or starts to move, check the working of the hydraulic circuit for leakage or filter issues to ensure there is enough oil flow. Make sure that the hydraulic oil pressure at the machine is minimum 60 bar (870 psi), increase the pressure if necessary and check the working of the low density kit, replace if necessary. Check the tailgate open sensor or the tailgate lock sensors and adjust the sensors, check the working and replace if necessary, if they are faulty or adjusted incorrectly.
M
Mary WilliamsAug 29, 2025
What should I do if the bale out sensor (BOS) is active when it is not allowed on my KUHN VBP 2190 Farm Equipment?
- A
  Amy ThomasAug 29, 2025
  If the bale out sensor (BOS) is active when it should not be, it could be due to pollution obstructing the BOS plate, so clean and grease the BOS plate. There might be a mechanical obstruction at the BOS plate, so check the movement and grease the BOS plate. The bale out sensor could be incorrectly adjusted or faulty, so adjust the sensor, check its working, and replace it if necessary.
S
Shelly BrewerAug 29, 2025
What to do if the KUHN VBP 2190 tailgate is not open or closed?
- E
  eric75Aug 29, 2025
  If the tailgate is not open or closed, check the workings of the hydraulic circuit for leakage, filter issues, or flow problems. Inspect for any mechanical blockage and remove it. If there is no electric power from PCB to the hydraulic block, contact your dealer. Ensure the hydraulic oil pressure at the machine is minimum 60 bar (870 psi), increasing the pressure if necessary, and check the working of the low density kit, replacing it if necessary. Finally, if the tailgate open sensor or the tailgate lock sensors are faulty or adjusted incorrectly, adjust the sensors, check their working, and replace them if necessary.
S
Sydney MccormickAug 28, 2025
Why is loading arm 1 not in the upper position within the time-out on my KUHN VBP 2190?
- R
  Ryan WardAug 28, 2025
  If loading arm 1 is not in the upper position within the time-out, it could be due to a mechanical obstruction, so check for any blockage and remove it. The hydraulic flow might be interrupted or too low, so check the hydraulic circuit for leakage or filter issues and ensure enough flow. The valve of loading arm 1 could be faulty, so check the valve, its 12 V electrical power, and for dirt. The sensor of loading arm 1 might be adjusted incorrectly or faulty, so adjust the sensor, check its operation, and replace it if necessary. Finally, if the bale is too heavy, decrease the diameter or reduce the bale chamber pressure to make less heavy bales.
C
Catherine GonzalezAug 27, 2025
What to do if the tailgate is not fully open on KUHN Farm Equipment?
- M
  Maria HunterAug 27, 2025
  If the tailgate is not fully open, check for any mechanical blockage and remove it. Also, verify the hydraulic flow is not interrupted or too low by checking the hydraulic circuit for leakage or filter issues and ensure there is enough oil flow. If there is no electric power from PCB to the hydraulic block, contact your dealer. Finally, if the gate Open Sensor adjustment is incorrect or faulty, adjust the sensor, check its working, and replace it if necessary.