Kurzweil KME61 - REV A

Questions and Answers

P
Peter BlackAug 14, 2025
Why is the sound from my Kurzweil KME61 - REV A KME61 low or distorted?
- K
  Kyle OwensAug 14, 2025
  If the sound from your KME61 is low or distorted, consider the following: * Check that the audio cables are securely plugged in at both ends. * Consult the 'Power Problems' section for power module issues. * Adjust MIDI Volume or Expression message settings. * If a control pedal is connected, ensure it's pressed down. * Set the input to the audio system for high impedance. * Adjust the input trim to a higher setting on your audio system or mixer.
A
Amber NguyenAug 17, 2025
What to do if there is no sound from my Kurzweil Recording Equipment KME61?
- L
  lmedinaAug 17, 2025
  If you're not getting any sound from your KME61, here are a few things to check: * Ensure the KME61 Volume slider is in the Up position. * If using a control pedal, make sure it's pressed down. * Increase the volume on your audio system or mixer. * Select the correct signal source on your audio system or mixer. * Make sure the audio cables are securely plugged in at both ends. * Verify you are using the correct type of audio cable.
G
gcabreraAug 20, 2025
What to do if my Kurzweil Recording Equipment isn’t turning on?
- J
  Johnathan PetersAug 20, 2025
  If your device isn't powering on, try these steps: * Make sure the power module is securely plugged into the wall outlet. * Check that the cord from the power module is fully plugged into the KME61. * Verify the input voltage rating of the power module matches your power system. * Use a power module that meets the specifications: 9.5VAC, 2.0 amp, center pin positive, 5.5mm OD, 2.5mm ID coax type plug. * Test with a different wall outlet, power strip, or extension cord.
D
Diana KingAug 25, 2025
What to do if my Kurzweil Recording Equipment control pedal does not work properly?
- L
  Lynn DiazAug 25, 2025
  If your control pedal isn't working right, check these: * Make sure the control pedal is plugged into the jack marked 'CC Pedal'. * Never use a control pedal that has a mono (two circuit) plug. * Check for a wiring problem if the pedal works backward, operates abruptly, or not at all. * Verify that the Y adapter is a stereo splitter type, if you are using adapter cables. * Use 'Active' volume pedals for control, as volume pedals typically don’t work well because of impedance or taper problems.
G
Garrett WhiteAug 27, 2025
How to fix problems sending MIDI from my Kurzweil KME61 - REV A to an external module?
- M
  Matthew SandovalAug 27, 2025
  To troubleshoot MIDI transmission issues: * Make sure the MIDI cable is securely plugged in at both ends. * Ensure you're using the correct MIDI connections: KME61’s MIDI Out to the module’s MIDI In. * Try replacing the MIDI cable, as it may be defective. * Confirm that the MIDI Transmit channel(s) specified match those of the receiving device.
B
Benjamin MolinaAug 30, 2025
How to fix problems with the internal sound module of my Kurzweil KME61 - REV A receiving MIDI from an external device?
- C
  Carla RiversAug 31, 2025
  To resolve issues with the internal sound module receiving MIDI: * Ensure the MIDI cable is securely plugged in at both ends. * Verify the MIDI connections: plug into the KME61’s MIDI In connector and the source’s MIDI Out connector.
T
Timothy RamirezSep 3, 2025
Why is the sustain stuck on when using the included pedal with my Kurzweil KME61 - REV A Recording Equipment?
- A
  Alexander SullivanSep 3, 2025
  If the sustain is stuck 'on' when using the included pedal, be sure the pedal is plugged in before switching on the power.
N
Nathan RuizSep 6, 2025
Why is the pedal acting backward on my Kurzweil KME61 - REV A Recording Equipment (active when up instead of down)?
- M
  Matthew IrwinSep 6, 2025
  If the pedal is acting backward, make sure the pedal is plugged in before turning the power on.
R
robert20Sep 9, 2025
How to resolve issues with control pedal taper and range on Kurzweil Recording Equipment?
- H
  Heidi GillSep 10, 2025
  To address control pedal taper and range issues: * If the taper isn't linear, run the Control Pedal diagnostic and check the reading when the pedal is pressed halfway down. * If the control range is less than 0-127, run the Control Pedal diagnostic and check the reading at both extremes of pedal motion.

Summary

Safety and Warnings

Risk of Electric Shock

Warning about not opening the cover and referring servicing to qualified personnel to avoid electric shock.

General Safety and Installation Instructions

Getting Started: Unpacking and Power

Connecting the Power Supply

Step-by-step guide for connecting the KME61's power adapter to the unit and wall outlet.

Getting Started: Connections and Play

Audio and Pedal Connections

Powering On and Initial Setup

Steps for turning on the KME61, recommended volume adjustment, and power supply placement advice.

Rear Panel Connections

Power and Audio Outputs

Details on the power switch, power jack, audio outputs, and headphone jack on the rear panel.

Pedal and MIDI Ports

Information on connecting pedals and the KME61's MIDI In, Out, and Thru ports.

Front Panel Overview

Front Panel Controls Explained

Front Panel Buttons and Functions

Soft, Value, and Select Buttons

Explanation of the functions of Soft, Value (+/-), Group/User Setup, and Program/Factory Setup select buttons.

Master Mode System Reset

Performing a System Hard Reset

Instructions for performing a system hard reset to restore the KME61 to its original factory condition.

Troubleshooting

Common Problems and Solutions

A list of frequently encountered problems and suggested troubleshooting steps.

Troubleshooting Power Issues

Steps to diagnose and resolve problems related to power supply and unit operation.

Troubleshooting Audio and MIDI

Resolving Audio Output Problems

Steps to troubleshoot issues with no sound, low volume, or distorted audio output.

Diagnosing MIDI Communication Issues

Steps to troubleshoot problems with sending or receiving MIDI data to/from external devices.

Troubleshooting Pedal Issues

Switch Pedal Troubleshooting

Steps to resolve problems with switch pedals, including proper connection and operation.

Control Pedal Troubleshooting

Steps to resolve issues with control pedals, covering wiring, compatibility, and operation.

Troubleshooting Advanced Issues

Initiating Diagnostics

Steps to start the KME61's built-in diagnostic software for component testing.

Diagnostic Procedures

Scan Diagnostic Functionality

How to use the Scan Diagnostic to test all controls and view their real-time values.

Diagnostic Testing of Controls

Testing Pitchbend and Modulation Wheels

How the Pitchbend and Modulation wheels are tested for proper function and value range.

Diagnostic Testing of Switches and Display

Testing Panel Buttons and LEDs

How panel buttons and their associated LEDs are tested for proper functionality.

Running the LCD Diagnostic

Steps to run the LCD Diagnostic to test the display's character rendering and cycling.

Engine Diagnostics Procedures

Accessing Engine Diagnostics

How to enter the Sound Engine diagnostic selection menu.

Selecting Diagnostic Test Modes

Automated Diagnostic Testing

Running AUTO Diagnostics

Kurzweil KME61 - REV A Specifications

General

Category	Recording Equipment
Model	KME61 - REV A
Number of Keys	61
Keyboard	Semi-Weighted
Aftertouch	Yes
Polyphony	32 voices
Multitimbral	16 parts
MIDI Ports	In, Out, Thru
Presets	256 Programs
Effects	Reverb, chorus
Display	LCD
Controllers	Pitch wheel, modulation wheel
Connections	headphone output
Dimensions	40.5 x 12.5 x 4 inches