Kurzweil PC3K7 - MIDI Program (Midiprog); Status; Input Channel

7-8
Setup Mode
The Channel/Program (CH/PROG) Page
MIDI Program (MidiProg)
MidiProgdefineswhichprogramnumberistransmittedouttheMIDIOutportonthecurrent
zone’sMIDIchannel.
WhenyouchangethevalueoftheProgramparameter,thevalueofMIDIProgautomatically
changescorrespondingly.IfyouwanttotransmitaMIDIprogramchangenumberdifferent
fromtheonecorrespondingtothe
localprogram,selectthelocalprogramfirst,thenchangethe
MIDIprogram.
DifferentprogramsareaccessibledependingonthevalueoftheBankModeparameter:
Status
ThisparameterdetermineswhatthecurrentzonedoeswhenyouselectthesetupinSetup
mode.Mutedmeansthatthezonesendsandreceivesprogramchangesandentry/exitcontroller
values,butdoesn’tplaynotes.IfthevalueisActive,thezonesendsandreceivesnormallyvia
MIDI.Solocausesonly
thecurrentzonetoplay,“backgrounding”allotherzones
(backgroundedzonessendandreceiveprogramchangesandentry/exitcontrollervalues,but
don’tplaynotes).WithavalueofSolo+Muted,thecurrentzoneisbothsoloedandmuted;when
thezoneisn’tsoloed,itwon’tproducesound).
Seethesectionaboutzone
‐statusLEDs(page 7‐4)formoreinformationabou tmutingand 
soloingzones.
Input Channel
InSetupmode,anexternalMIDIdevice(suchasakeyboardorsequencer)willplaynotesofa
singleprogrambydefault(iftheLocalKeyboardChannelparameterissettooff,seepage 10‐10
fordetails.)TheplayedprogramwillbeonaZonethathasaChannelparameter(on
theCH/
PROGpage)whichmatchesthechannelonwhichtheexternalMIDIdeviceistransmitting.(If
noZone’sChannelparametermatches,theexternaldevicewillplaynotesofthelastprogram
thatwasusingthatchannelinProgramModeorfromapreviouslyload ed SongorSetup.)
WhentheProgram
ofaSetupZoneisplayedthisway,SetupMIDIparameters(mostnoticeably
keyrangeandtransposition)willnotbeapplied.Ifyouwanttheseparametersapplied,setthe
InputChannelparametertomatchthechannelonwhichtheexternalMIDIdeviceis
transmitting.ToplaytheentireSetupfrom
anexternalMIDIdevice,seeLocalKeyboardChannel
(LocalKbdCh) on page 10‐10.WhenLocalKeyboardChannelissettosomethingotherthanOff,
theInputChannelparameterhasnoeffectandwillappearinparentheses.InputChannel
basicallyhasthesameeffectasLocalKeyboardChannel,exceptyoucanchoosetoplay
onlyone
orsomeSetupZonesformanexternaldevice,insteadofallZones.ToplaymorethanoneZone
fromanexternaldevice,seteachdesiredZone’sInputChannelparametertomatchthechannel
onwhichtheexternalMIDIdeviceistransmitting.Itisalsopossibletousethe
InputChannel
parametertousemultipleexternaldeviceswhicheachplayaspecificZoneorZones.Fordetails
oncontrollingassignmentsmadetothePC3K’sphysicalcontrollers(sliders,switches,mod
wheel,etc.)fromanexternalMIDIdevice,seeContinuousControllerMessagesFromExternalMIDI
Devices on page 10‐10.
Value of BankMode Available Programs
Ctl 0 or Ctl 32 0 to 127
Ctl 0/32 0 to 127
K2600 0 to 99
None None