Kwikset Powerbolt2 - User Manual

ENGLISH
D
If needed, re-key the lock to
work with your existing key.
See the supplied SmartKey
Re-key instructions for more
information.
Re-key the lock Program the lock
Programming
instructions are
located on the
reverse side of
this document.
B
J (2x)
Install strike
2-1/8"
54 mm
1-1/2"
38 mm
A
C
B
C
Prepare exterior keypad (if needed)
For doors with 2-1/8" (54 mm) holes For doors with 1-1/2" (38 mm) holes
Proceed to step 5. Temporarily remove gasket
Reinstall gasket,
ensuring a tight seal.
Remove adapter ring
A B C
D E
C
L
F
L (2x)
L
E
Cable goes
underneath latch
Locate screws (L)
and keep them
within reach.
Keep parallel to
edge of door
Tighten
screws
evenly
Insert key and test latch.
If latch does not extend
or retract smoothly,
adjust screws (L).
Remove key when
nished and make sure
the latch bolt is in the
unlocked position.
Install keypad and mounting plate
Use and programming
instructions are located on the
reverse side of this document.
AA
Required Tools
Additional Tools (depending on application)
Installation Guide
180°
A B
A / A2
Hold the latch in front of the
door hole, with the latch face
ush against the door edge.
If the latch holes are
centered in the door hole, no
adjustment is required.
Proceed to step 3.
If the latch holes are NOT
centered, adjust latch. See
“Latch Adjustment.”
Latch Adjustment (only if needed)
Adjust the backset of latch (if needed)
A
A2
J (2x)
A
B
Install latch
For doors with chiseled edge For doors without chiseled edge
wood
block
1-3/4" (44 mm)
1-3/8" (35 mm)
2-3/8" (60 mm)
2-3/4" (70 mm)
Fold
If your door requires drilling, cut out the template and place it on the exterior side of the door.
Complete door drilling instructions are available at www.kwikset.com/doorprep.
Template
Edge
Backset
Face
Centerline
A
A2
B
J
C
E
F
G
H
K
L
D
Kwikset
1-800-327-5625
www.kwikset.com
If needed, please contact
Kwikset to order a drive-in
latch for your lock.
Parts in the Box
Latch and Strike Exterior Assembly Interior Assembly
Fasteners
1"
25 mm
2-1/8"
54 mm
1-1/2"
38 mm
1-3/8" — 1-3/4"
35 mm — 44 mm
Check dimensions
Additional door preparation may be
required for doors with 1-1/2" (38 mm)
holes. Consult the drilling instructions at
www.kwikset.com/doorprep.
2-3/8" (60 mm)
or
2-3/4" (70 mm)
or
F
2-1/8"
54 mm
1-1/2"
38 mm
Prepare mounting plate (if needed)
For doors with 2-1/8" (54 mm) holes For doors with 1-1/2" (38 mm) holes
Proceed to step 6.
Use pliers to remove the two tabs from the mounting plate (F).
A B C
AA
4x
G
H
Press and hold the
Reset button on the
interior assembly for
ve seconds, until you
hear three beeps.
Load batteries and reset the lock
Ensure correct polarity. For best
results, use new, non-rechargeable
Alkaline batteries only.
Note: The turnpiece
may rotate on its own.
A B C D E F
G
G
K (3x)
Rotate turnpiece
AWAY from the
door edge.
Check for smooth turnpiece rotation.
If turnpiece does not rotate, pull
interior assembly (G) off the door.
Repeat steps 7B and 7C, making
sure the turnpiece is rotated
away from the door edge.
Make sure
door is
unlocked.
door
edge
45°
Align colored edges of
connectors and ensure
secure cable connection.
Install interior assembly
A
While the door is OPEN AND UNLOCKED, enter the following code to teach the lock the orientation of the door.
B C
Press the Lock
button once.
If programming is successful,
the keypad will ash green
twice with two beeps.
If unsuccessful, the keypad will
ash red three times with three
beeps. Attempt to enter the
code again.
Default
MASTERCODE:
0-0-0-0
Lock
button
Lock
button
“0”
D
If the latch bolt
extends to lock,
the lock has
correctly learned
the orientation of
the door.
Unlock
door.
IMPORTANT: Enter door handing code and test lock
3 4 5 6
7 98
10 11 12
1 2
49697 / 01

Summary

Kwikset Powerbolt 2 Installation

Check Dimensions and Backset

Verify door and backset dimensions, adjusting latch if necessary for proper fit.

Install Latch and Prepare Door

Install the latch mechanism into the door and prepare the exterior keypad and mounting plate.

Mounting Plate and Exterior Assembly

Install the mounting plate and exterior assembly, ensuring correct cable routing.

Install Interior Assembly and Batteries

Load batteries and install the interior assembly, ensuring correct cable connections and turnpiece alignment.

Critical Door Handing and Testing

Enter door handing code to teach the lock orientation, then test the lock's functionality.

Final Installation and Programming

Install the strike, re-key the lock if needed, and program the lock with user codes.

Door Preparation Template

Cut out and use the template for accurate door drilling and preparation for installation.

Kwikset Powerbolt2 Specifications

General

Type	Electronic Deadbolt
Keypad	Yes
Battery	4 AA batteries
Battery Life	Approximately 1 year
Finish Options	Satin Nickel, Venetian Bronze, Polished Brass
User Codes	Up to 6
Auto-Lock	Yes
Compatibility	Standard doors
Number of Keys Included	2
Batteries Required	Yes
Adjustable Latch	Yes
Backset	Adjustable 2-3/8" or 2-3/4"
Connectivity	No
Backup Power	No
Power Source	Battery Powered
Door Thickness	1-3/8" to 1-3/4"
Locking Mechanism	Motorized
Keyway	Kwikset KW1