To Next PageTo Next Page
Need help?Do you have a question about the KYMCO BET & WIN 50 and is the answer not in the manual?
General| Fuel System | Carburetor |
|---|---|
| Ignition | CDI |
| Starting System | Electric & Kick |
| Front Suspension | Telescopic Fork |
| Brakes Front | Disc |
| Brakes Rear | Drum |
| Tire Size Front | 120/70-12 |
| Tire Size Rear | 130/70-12 |
| Cooling System | Air Cooled |
| Transmission | Automatic |
Outlines the manual's scope, describing sections on precautions, frame covers, inspection, engine, chassis, and electrical systems.
Locates and identifies the vehicle and engine serial numbers.
Provides detailed technical specifications for the motorcycle.
Essential safety rules and precautions for performing service operations.
Lists torque specifications and specialized tools required for maintenance.
Identifies lubrication points and presents the electrical system wiring diagram.
Diagnostic flowcharts for common engine starting and running problems.
Covers service information, torque values, and troubleshooting for noisy mufflers.
Step-by-step instructions for removing various frame covers and body panels.
Instructions for safely removing the exhaust muffler and its related parts.
Safety warnings, engine/chassis specifications, and torque values for inspection.
Detailed schedule for periodic inspections and maintenance of vehicle components.
Procedures for inspecting fuel lines, filters, and adjusting throttle operation.
Guidance on servicing the air cleaner, spark plug, and checking ignition timing.
Methods for testing cylinder compression and checking final reduction gear oil.
Inspection of the drive belt and adjustment of the headlight aim.
Procedures for coolant level checks and brake system inspections.
Checks on chassis nuts/bolts, wheels/tires, steering, and suspension components.
Inspection of oil filter, oil pump condition, and associated lubrication points.
Steps for removing the oil pump and inspecting its components for wear or damage.
Instructions for installing the oil pump and bleeding air from the system.
Procedures for removing and servicing the engine oil tank.
Parts requiring engine removal and associated torque specifications.
Step-by-step guide for disconnecting and removing the engine from the motorcycle.
Instructions for reinstalling the engine and performing necessary adjustments.
General instructions, specifications, torque, and troubleshooting for cylinder parts.
Procedure for removing the cylinder head and inspecting it for warpage.
Steps for removing, inspecting, and installing the cylinder and piston components.
Specifications, torque values, special tools, and troubleshooting for pulley systems.
Procedures for removing and inspecting the kick starter spindle and related parts.
Inspection and replacement of the drive belt and servicing of the drive pulley.
Instructions for removing, disassembling, inspecting, and assembling clutch/driven pulley.
Specified oil, tools, and troubleshooting for the final reduction gear unit.
Steps for disassembling final reduction gears and inspecting for wear or damage.
Procedures for replacing bearings in the final reduction assembly.
General instructions, torque value, and special tools for A.C. generator maintenance.
Detailed steps for removing and reinstalling the A.C. generator.
Service information, specifications, tools, and troubleshooting for crankcase/crankshaft.
Steps for separating crankcase halves and removing the crankshaft.
Procedures for inspecting crankshaft runout, clearances, and bearings for installation.
Steps for assembling the crankcase halves, including dowel pins and oil seals.
General instructions, torque values, and troubleshooting for the cooling system.
Details coolant capacity, thermostat operation, and coolant mixing ratios.
Procedures for inspecting the radiator for leaks and removing it.
Inspection and replacement of water pump seals and the thermosensor.
Procedure for inspecting thermostat operation and reinstalling it.
Specifications, troubleshooting, and special tools for fuel and carburetor systems.
Steps for disassembling and installing the throttle valve assembly.
Procedures for removing the carburetor and adjusting the air screw.
Inspection and servicing of the auto bystarter and float chamber.
Procedures for removing, inspecting, and installing the fuel pump and fuel strainer.
Specifications, torque values, and troubleshooting for front end components.
Steps for removing and reinstalling the handlebars and associated controls.
Procedures for removing and installing the front wheel, including bearings.
Disassembly, inspection, and assembly of the front brake master cylinder and caliper.
Instructions for servicing front shock absorbers and front fork components.
Specifications, torque values, and troubleshooting for rear end components.
Procedures for rear wheel removal/installation and rear brake drum inspection.
Instructions for removing, disassembling, and assembling rear shock absorbers.
General instructions, specifications, and troubleshooting for electrical systems.
Diagnosing charging system issues and battery inspection/charging procedures.
Continuity tests and inspection for ignition coil, CDI unit, and starter system.
General instructions and troubleshooting for instruments, switches, and lights.
Procedures for inspecting the fuel unit and checking the oil meter operation.
Checking switch continuity and instructions for bulb replacement.
Procedures for removing instruments and replacing headlight bulbs.
Description of the catalytic converter system and its function.
Instructions for removing, inspecting, and installing the exhaust muffler.
Checks and adjustments for air cleaner, carburetor, and ignition system for emissions.
