To Next PageTo Next PageWhy is the driveline telescoping tube wearing on my Land Pride RCR2596 Cutter?
If the driveline telescoping tube is wearing on your Land Pride Cutter, it needs lubrication. Lubricate it every 20 hours.
Why are the blades breaking on my Land Pride Farm Equipment?
Blades break on Land Pride Farm Equipment primarily from hitting solid objects, so avoid doing that. Another reason is blades hitting each other, in which case blade carriers need to be timed.
What to do if the tail wheel support is failing on my Land Pride RCR2596?
If the tail wheel support is failing on your Land Pride Cutter, it may be due to lowering it too fast or hitting objects when turning. Adjust the rate of drop and reduce speed on turns to mitigate this.
How to fix an oil seal leak on my Land Pride RCR2596 Cutter?
If the oil seal is leaking on your Land Pride Cutter, it could be because the gearbox is overfilled, the seals are damaged, or grass/wire is wrapped on the shaft in the seal area. Here's how to address it: * Drain the gearbox to the side plug hole if it's overfilled. * Replace the seals if they are damaged. * Check seal areas daily for grass or wire.
Why are the blades wearing excessively on my Land Pride RCR2596?
Blades on your Land Pride Cutter can wear excessively if you're cutting on sandy ground or contacting the ground frequently. To solve this, raise the cutting height.
Why is the driveline yoke or cross failing on my Land Pride Cutter?
If the driveline yoke or cross is failing on your Land Pride Cutter, it could be due to shock load or lack of lubrication. To fix this, avoid hitting solid objects and lubricate every 8 hours.
Why are the blades breaking on my Land Pride RCR2596 Cutter?
Blades on your Land Pride Cutter may break due to hitting solid objects or the blades hitting each other. To prevent this, avoid hitting solid objects. If the blades are hitting each other, the blade carriers need to be timed.
What to do if the driveline clutch is slipping on my Land Pride RCR2596 Cutter?
Driveline clutch slippage in your Land Pride Cutter can occur if you're scalping the ground, cutting too fast, engaging the PTO too quickly at high engine RPM, or cutting over solid objects. To resolve this: * Raise the cutting height. * Reduce travel speed. * Slowly engage the PTO at low engine RPM. * Avoid solid objects.
Why is there excessive vibration in my Land Pride RCR2596 Cutter?
Excessive vibration in your Land Pride Cutter can stem from several issues. It could be due to a bent driveline, loose blades, a bent blade carrier, a broken blade, a blade that won't swing freely, or blades with unequal weight. To address this, try the following: * Replace the driveline if it's bent. * Tighten any loose blade bolts. * Replace the blade carrier if it's bent. * Replace any broken blades. * Remove and inspect blades that won't swing. * Replace both blades if they have unequal weight.
Why are the blades coming loose on my Land Pride Farm Equipment?
Blades come loose on Land Pride Farm Equipment because they were not tightened properly, so tighten the blade hardware referring to Cutter Blade Maintenance on page 36. Another reason is improper deck attitude, so lower the front of the deck, see page 22.
General| Brand | Land Pride |
|---|---|
| Model | RCR2596 |
| Category | Cutter |
| Language | English |
General safety practices for operating machinery.
Explains the meaning of safety alert symbols and signal words.
Procedures for safely shutting down and storing equipment.
Importance and proper use of safety chains for towing.
Guidelines for safe transportation of equipment.
General advice for performing maintenance safely.
Recommended personal protective equipment for safe operation.
Hazards and precautions related to high-pressure hydraulic fluids.
Prohibits carrying riders on equipment.
Explains the importance and placement of safety labels.
Describes the intended uses and features of the rotary cutters.
Guidance on how to use the operator's manual effectively.
Information on dealer support and warranty registration.
Specifies the tractor horsepower and weight needed for operation.
A list of items to check before assembling the cutter.
Step-by-step procedure for safely shutting down the tractor.
Step-by-step guide to assembling the pull-type hitch.
Instructions for installing equal angle drivelines.
Instructions for installing constant velocity drivelines.
Steps for connecting a pull-type cutter to a tractor.
Step-by-step guide to assembling the 3-point hitch.
Steps for connecting a 3-point cutter to a tractor.
Steps for connecting the driveline to the tractor and implement.
Procedure to check driveline length to prevent damage.
Steps to verify no interference between components.
Installation and use of check chains for cutting height control.
Instructions for installing optional chain safety guards.
Instructions for installing optional rubber safety guards.
Adjustments for deck leveling and cutting height on pull-type units.
Adjusting the cutting height mechanism on pull-type units.
Adjustments for deck leveling and cutting height on 3-point units.
How to level the cutter deck side-to-side.
How to level the cutter deck front-to-back.
Adjusting the tailwheel for proper cutting height.
Pre-operation checks for safe and efficient use.
Pre-operation inspections before starting the cutter.
Guidelines for safe transport of the rotary cutter.
Procedures for engaging and disengaging cutter blades.
How to safely cross ditches and banks.
Recommended turning angles for pull-type cutters.
Steps for safely unhooking a 3-point cutter.
Steps for safely unhooking a pull-type cutter.
General guidelines for efficient and safe operation.
General maintenance advice for longevity.
Tips for maintaining hydraulic system health.
Procedures for inspecting, sharpening, and replacing blades.
Maintenance and replacement of skid shoes.
Explanation and run-in procedure for the slip-clutch.
Procedures for storing the implement for long periods.
Information on how to order replacement parts and colors.
Details on lubrication points and intervals for various components.
Lubrication and oil level checks for the gearbox.
Detailed specifications and capacities of the RCR25 Series cutters.
Features and benefits of the RCR25 Series rotary cutters.
A chart listing common problems, causes, and solutions.
Chart of torque values for various bolt sizes and grades.
Recommended tire inflation pressures.
Details of the Land Pride product warranty.
