3
Lightly tighten Hex screw
with a ⁄ hex key to retain
position. When you are
finished, you can remove
the adjusted die from
the press by rotating the
spline drive bushing ⅓ of
a turn counterclockwise.
When you use it next time,
it will return to perfect
adjustment.
Install cartridge specific
X-PRESS shell holder into shell
holder adapter. Attach clear
bottle to adapter if depriming.
Install this
assembly in the
base casting, and
secure with a ⅓
of a turn counter
clockwise.
The shell
holder lips should
be set parallel to the
slide rail to allow
case feeding.
Place lock ring inside the bottle
adapter. Install the bottle adapter
on to the shell holder adapter as
shown.
Loosen the hex screw on the
spline drive bushing with ⁄
hex key.
Available accessory
# 91634 ⁄ hex key
Remove the
lock-ring
from your
die, and
install. Adjust
according to
your reloading
die set
instructions.
CONFIGURING APP FOR RELOADING
Lock
Ring
inside
Shell holder adapter
X-PRESS
shell
holder
Using Universal Decapping Die?
You may want to consider adding
a heavy duty guided decapper to
the die. Guided decapper aligns
the case and decapping pin,
reducing the likelihood of bending
or breaking the pin.
order more bushings:
2 pack Product # 90063
3 pack Product # 90042
4 pack Product # 90095
Caliber
Product #
Caliber
Product #
17 cal. & 204 Ruger
91574 30 cal. 91580
22 cal. 91576 34 cal. to 35 cal. 91581
6mm to 25 cal. 91577 40 cal. 91583
27 cal. to 7mm 91578 45 cal. 91584
X-PRESS SHELL HOLDERS
X-PRESS shell holders
make the nicest single
stage press, the fastest. A
word about X-PRESS shell holders.
The X-PRESS shell holder allows
easy automation on the APP press,
however, the pass through design
reduces the amount of “pull” that
can be applied to the cartridge. That
said, we do not recommend full
length resizing rimless bottle neck
cases. If you insist, we suggest using only Lee dies and Lee case resizing lubricant # 90006. Only Lee dies
include a built-in stuck case remover in the event you damage a rim and stick a case.
Product # Cartridges Product # Cartridges
91534 1 38 Long & Short Colt, 38 SPL, 357 MAG 91544 11 44 SPL/MAG, 45 Colt, 303 Sav.
91535 2 45 ACP, 308 Win., 30-06 91545 12 22 PPC, 6 PPC, 7.62x39R
91536 3 30/30, 6.5x55 Mauser, 32/40 91546 13 45 Auto Rim
91537 4 223 Rem, 5.56 NATO, 300 Blackout 91547 14 44/40, 45 Long Colt
91538 5 WSM’s, 7mm Rem Mag, 303 British 91548 15 25 ACP
91539 6 218 Bee, 25/20, 32/20 91549 16 7.62x54R, 500 S&W
91540 7 30 M-1, 32 ACP 91552 19 40 S&W, 9mm Luger
91541 8 33 Win, 348 Win, 40/65, 45/70 91553 20 17 Hornet, 22 Hornet
91542 9 41 Magnum 91554 21 6.8 Rem SPC, 224 Valkyrie
91543 10 220 Swift, 6.5 Jap, 7x64 Brenneke
The
X-PRESS
shell
holder
should
rotate
freely
To Next Page
Loading...
