Lenze EVS9322-ES

Appendix
11-29
 BA9300SU EN 2.1
Code ImportantPossible settingsLCDCode Important
ChoiceLenze
LCD
C0356
1
2
3
4
&$1 %227 83
287 EWEMF
287 EWEMF
&$1 '(/$<
3000
0
0
20
0 {1 ms} 65000 CAN bus time settings
1: CAN Boot-Up
2: CAN-OUT2 cycle
3: CAN-OUT3 cycle
4: CAN OUT 2/3 delay time
[C0357]
1
2
3
&(NO1JS SJNF
&(NO1JS SJNF
&(NO1JS SJNF
3000
3000
3000
0 {1 ms} 65000 CAN bus monitoring time for I
ratedx
C0358
5FRFS 1O'F
0 0 no function
1 CAN reset
Install CAN bus reset node
C0359
&$1 RSDSF g
0 Operational
1Pre-Operat
2 Warning
3 Bus off
CAN bus status:
C0360
1
2
3
4
5
6
7
8
9
10
11
12
0FRRDHF 287
0FRRDHF ,1
0FRRDHF 287
0FRRDHF 287
0FRRDHF 287
0FRRDHF 3287
0FRRDHF 3287
0FRRDHF ,1
0FRRDHF ,1
0FRRDHF ,1
0FRRDHF 3,1
0FRRDHF 3,1
g
0 {1} 65535 Telegram counter (number of telegrams, with
values > 65535 counting starts again at 0)
1: all sent
2: all received
3: sent to CAN-OUT1
4: sent to CAN-OUT2
5: sent to CAN-OUT3
6: sent to parameter channel 1
7: sent to parameter channel 2
8: received from CAN-IN1
9: received from CAN-IN2
10: received from CAN-IN3
11: received from parameter channel 1
12: received from parameter channel 2
C0361
1
2
3
4
5
6
7
8
9
10
11
12
/OD' 287
/OD' ,1
/OD' 287
/OD' 287
/OD' 287
/OD' 3287
/OD' 3287
/OD' ,1
/OD' ,1
/OD' ,1
/OD' 3,1
/OD' 3,1
g
0 {1 %} 100 CAN bus load
• To ensure a perfect operation, the total bus
load (all connected devices) should be less
than 80%
1: all sent
2: all received
3: sent to CAN-OUT1
4: sent to CAN-OUT2
5: sent to CAN-OUT3
6: sent to parameter channel 1
7: sent to parameter channel 2
8: received from CAN-IN1
9: received from CAN-IN2
10: received from CAN-IN3
11: received from parameter channel 1
12: received from parameter channel 2
C0362
6W1E EWEMF
1.000 -32.000 {1.000 ms} 32.000 Time between two sync telegrams on the
system bus
C0363
6W1E EO55
1 1{1} 5
10.8
µs
21.6
µs
32.4
µs
43.2
µs
54.0
µs
Correction value for C0362
[C0364]
&$1 DESJT
1000 see selection list 2
FIXED 0
Pre-operat. after operat.
Activate process data externally
Change over from pre-operation to operation
C0365
&$1 DESJT g
01Pre-operat. after operat.
Input signal CAN active
C0366
6W1E 5FRPO1RF
1 0 no sync response
1 sync response
CAN Sync Response
C0367
6W1E 5V ,'
128 1 {1} 256 CANSyncRxIdentifier
C0368
6W1E 7V ,'
128 1 {1} 256 CANSyncTxIdentifier