Lenze EVS9322-ES - Page 164

Appendix
11-45
 BA9300SU EN 2.1
Code ImportantPossible settingsLCDCode Important
ChoiceLenze
LCD
C0932
5() NO'F
0
0 Mode 0
1 Mode 1
6 Mode 6
7 Mode 7
8 Mode 8
9 Mode 9
20 Mode 20
21 Mode 21
Homing mode
C0933
5() S5D1R
0
0 Rising trans
1 Falling trans
Reference signal transition
rising transition
falling transition
C0934
5() OGGRFS
0 -2140000000 {1 inc} 2140000000 Home position offset
C0935
5() RPFF'
2.0000 0.0001 {0.0001 % N
max
} 100.0000 Homing speed
C0936
5() 7J
1.00 0.01 {0.01 s} 990.00 T
i
time homing
• Tir and Tif are identical
C0940
18NF5DSO5
1 -32767 {1} 32767 CONV1 Numerator
C0941
'F1ONJSDSO5
1 1 {1} 32767 CONV1 Denominator
[C0942]
J1
1000 FIXED 0 % → Selection list 1 Configuration analog input CONV1
C0943
& g
-199.99 {0.01 %} 199.99 Display of C0942
C0945
18NF5DSO5
1 -32767 {1} 32767 CONV2 numerator
C0946
'F1ONJ1DSO5
1 1 {1} 32767 CONV2 denominator
[C0947]
J1
1000 FIXED 0 % → Selection list 1 Configuration analog input CONV2
C0948
& g
-199.99 {0.01 %} 199.99 Display of C0947
C0950
18NF5DSO5
1 -32767 {1} 32767 CONV3 numerator
C0951
'F1ONJ1DSO5
1 1 {1} 32767 CONV3 denominator
[C0952]
J1
1000 FIXEDPHI0 →Selection list 4 Configuration analog input CONV3
C0953
& g
-32767 {1 rpm} 32767 Display of C0952
C0955
18NF5DSO5
1 -32767 {1} 32767 CONV4 numerator
C0956
'F1ONJ1DSO5
1 1 {1} 32767 CONV4 denominator
[C0957]
J1
1000 FIXEDPHI0 → Selection list 4 Configuration analog input CONV4
C0958
& g
-32767 {1 rpm} 32767 Display of C0957
C0960
)81ESJO1
1 1{1} 3Function
1Characteristic1
2Characteristic2
3Characteristic3
C0961
W
0.00 0.00 {0.01 %} 199.99
C0962
W
50.00 0.00 {0.01 %} 199.99
C0963
W
75.00 0.00 {0.01 %} 199.99
C0964
W
100.00 0.00 {0.01 %} 199.99
C0965
V
50.00 0.01 {0.01 %} 99.99
C0966
V
75.00 0.01 {0.01 %} 99.99
[C0967]
J1
1000 FIXED0% → Selection list 1 Characteristic CURVE1-IN
C0968
& g
-199.99 {0.01 %} 199.99 Display of C0967
[C0970]
1RFS
1000 FIXED0% → Selection list 1 Speed input of the mains failure control
Setpoint path
[C0971]
GD8MS
1000 FIXED0 → Selection list 2 Input mains failure detected, input for
activation
[C0972]
5FRFS
1000 FIXED0 → Selection list 2 Reset input mains failure control
[C0973]
D'DPS
1000 FIXED0% → Selection list 1 Adaptation of P-gain of the voltage controller
[C0974]
EO1RS
1000 FIXED0% → Selection list 1 Adaptation of P-gain of the voltage controller
[C0975]
SI5FRI/'
1000 FIXED0% → Selection list 1 Restart protection when the value falls below
the speed threshold
[C0976]
1DES
1000 FIXED0% → Selection list 1 Comparison of threshold function
• Start for V
2
controller
[C0977]
RFS
1000 FIXED0% → Selection list 1 Speed start value
[C0978]
'ERFS
1000 FIXED0% → Selection list 1 Setpoint DC-bus voltage
C0980
9P
0.500 0.001 {0.001} 31.000 MFAIL Vp (gain)
C0981
71
100 20 {0.1 ms} 2000 MFAIL Tn (adjustment time)