Lenze I51AE175B - Page 481

Address Designaon Default seng Category Data type Factor A M
0x4024:003
(P615.03)
Automac rinsing: Rinse speed 0.0 Hz general I16 10 P -
0x4024:004
(P615.04)
Automac rinsing: Rinse period 0.0 s general U16 10 P -
0x4025
(P800.00)
Sequencer mode Disabled [0] general U8 1 P -
0x4026:001
(P801.01)
Sequencer segment 1: Frequency setpoint 0.0 Hz general I16 10 P -
0x4026:002
(P801.02)
Sequencer segment 1: Acceleraon/deceleraon 5.0 s general U16 10 P -
0x4026:003
(P801.03)
Sequencer segment 1: Time 0.0 s general U32 10 P -
0x4026:004
(P801.04)
Sequencer segment 1: Digital outputs 0 general U8 1 P -
0x4026:005
(P801.05)
Sequencer segment 1: Analog outputs 0.00 VDC general U16 100 P -
0x4026:006
(P801.06)
Sequencer segment 1: PID setpoint 0.00 PID unit general I16 100 P -
0x4026:007
(P801.07)
Sequencer segment 1: Torque setpoint 100.0 % general I16 10 P -
0x4026:008 Sequencer segment 1: NetWordOUT2 0 general U16 1 P -
0x4026:009 Sequencer segment 1: Reserved 0 general U32 1 P -
0x4027:001
(P802.01)
Sequencer segment 2: Frequency setpoint 0.0 Hz general I16 10 P -
0x4027:002
(P802.02)
Sequencer segment 2: Acceleraon/deceleraon 5.0 s general U16 10 P -
0x4027:003
(P802.03)
Sequencer segment 2: Time 0.0 s general U32 10 P -
0x4027:004
(P802.04)
Sequencer segment 2: Digital outputs 0 general U8 1 P -
0x4027:005
(P802.05)
Sequencer segment 2: Analog outputs 0.00 VDC general U16 100 P -
0x4027:006
(P802.06)
Sequencer segment 2: PID setpoint 0.00 PID unit general I16 100 P -
0x4027:007
(P802.07)
Sequencer segment 2: Torque setpoint 100.0 % general I16 10 P -
0x4027:008 Sequencer segment 2: NetWordOUT2 0 general U16 1 P -
0x4027:009 Sequencer segment 2: Reserved 0 general U32 1 P -
0x4028:001
(P803.01)
Sequencer segment 3: Frequency setpoint 0.0 Hz general I16 10 P -
0x4028:002
(P803.02)
Sequencer segment 3: Acceleraon/deceleraon 5.0 s general U16 10 P -
0x4028:003
(P803.03)
Sequencer segment 3: Time 0.0 s general U32 10 P -
0x4028:004
(P803.04)
Sequencer segment 3: Digital outputs 0 general U8 1 P -
0x4028:005
(P803.05)
Sequencer segment 3: Analog outputs 0.00 VDC general U16 100 P -
0x4028:006
(P803.06)
Sequencer segment 3: PID setpoint 0.00 PID unit general I16 100 P -
0x4028:007
(P803.07)
Sequencer segment 3: Torque setpoint 100.0 % general I16 10 P -
0x4028:008 Sequencer segment 3: NetWordOUT2 0 general U16 1 P -
0x4028:009 Sequencer segment 3: Reserved 0 general U32 1 P -
0x4029:001
(P804.01)
Sequencer segment 4: Frequency setpoint 0.0 Hz general I16 10 P -
0x4029:002
(P804.02)
Sequencer segment 4: Acceleraon/deceleraon 5.0 s general U16 10 P -
* Default seng depending on the size. Firmware version 05.00.00.00
Appendix
Parameter aribute list
481