How to replace defective imaging unit on Lexmark All in One Printer?
To resolve this issue with your Lexmark All in One Printer, replace the defective imaging unit. If you do not have a replacement imaging unit, visit www.lexmark.com for ordering information.
What does 'Supply needed to complete job' mean on Lexmark MX410 All in One Printer?
To resolve this issue on your Lexmark All in One Printer, install the missing supply to complete the job, or cancel the current job.
What to do when Lexmark MX410 All in One Printer says 'Imaging unit very low'?
Your Lexmark All in One Printer indicates that the imaging unit is very low and may need replacement soon. Select Continue on the printer control panel to clear the message and continue printing.
What does 'Serial option error' mean on Lexmark MX410?
To address a serial option error on your Lexmark All in One Printer, ensure the serial cable is properly connected and is the correct one for the serial port. Also, verify that the serial interface parameters (protocol, baud, parity, and data bits) are set correctly on both the printer and computer. You can also select Continue on the printer control panel to continue printing, or turn off the printer and then turn it back on.
Why does my Lexmark MX410 All in One Printer say 'Configuration change, some held jobs were not restored'?
This message on your Lexmark All in One Printer appears because the printer firmware has been updated, the tray for the print job has been removed, the print job was sent from a flash drive that is no longer attached, or the printer hard disk contains print jobs that were stored when the hard disk was installed in a different printer model. From the printer control panel, select Continue to clear the message.
What does 'Fax server not set up' mean on Lexmark All in One Printer?
To resolve this issue with your Lexmark All in One Printer, select Continue on the printer control panel to clear the message. Complete the Fax Server setup.
What does 'Too many trays attached' mean on Lexmark All in One Printer?
To resolve this issue on your Lexmark All in One Printer: 1. Turn off the printer. 2. Unplug the power cord from the electrical outlet. 3. Remove the extra trays. 4. Connect the power cord to a properly grounded electrical outlet. 5. Turn the printer back on.
How to clear 'Imaging unit low' message on Lexmark MX410?
Your Lexmark All in One Printer indicates that the imaging unit is low. You may need to order a new imaging unit. If you wish to continue printing, select Continue on the printer control panel to clear the message.
How to replace imaging unit on Lexmark All in One Printer when 0 pages remain?
To resolve this issue on your Lexmark All in One Printer, replace the imaging unit to continue printing. If you do not have a replacement imaging unit, visit www.lexmark.com for ordering information.
How to clear 'Cartridge low' message on Lexmark MX410?
Your Lexmark All in One Printer indicates that the toner cartridge is low. You may need to order a new toner cartridge. If you wish to continue printing, select Continue on the printer control panel to clear the message.
Guide on how to access and use the printer's web-based interface for configuration.
Details on installing memory cards, fonts, firmware cards, and other internal components.
Instructions for installing physical hardware options like trays and network adapters.
Steps for installing the necessary printer drivers and software on your computer.
Step-by-step guide for connecting the printer to an Ethernet network.
Instructions on how to perform basic copying tasks using the printer.
Configuration steps to enable and set up the printer's email functionality.
Initial setup and connection procedures for using the printer's fax capabilities.
Instructions for scanning documents directly to network folders.
Steps for scanning documents to a File Transfer Protocol (FTP) server.
Procedures for securely erasing device settings and data from the printer.
Tips and procedures to prevent paper jams in the printer.
General| Print Technology | Laser |
|---|---|
| Print Speed | Up to 40 ppm |
| Print Resolution | 1200 x 1200 dpi |
| Scan Type | Flatbed, ADF |
| ADF Capacity | 50 sheets |
| Duplex Printing | Yes |
| Standard Memory | 256 MB |
| Display | 2.4-inch color LCD |
| Functions | Print, Copy, Scan, Fax |
| Max Copying Speed | Up to 40 cpm |
| Max Copying Resolution | 600 x 600 dpi |
| Max Printing Speed | Up to 40 ppm |
| Optical Resolution | 1200 x 600 dpi |
| Fax Transmission Speed | 33.6 Kbps |
| Processor Speed | 800 MHz |
| Operating System Compatibility | Windows, Mac, Linux |
| Connectivity | USB, Ethernet |
| Paper Capacity | 250 sheets |
| Mobile Printing | Yes |
To Next Page
