LG 19LC2D - Page 76

12. Sharpness (Command: k k)
To adjust screen sharpness.
You can also adjust sharpness in the Picture menu.
Transmission [k] [k] [ ] [Set ID] [ ] [Data] [Cr]
Data Min: 0 - Max: 64 (*transmit by Hexadecimal code)
*Refer to 'Real data mapping 1 ' as shown below.
Acknowledgement [k] [] [Set ID] [] [OK/NG] [Data] [x]
13. Remote Control Lock Mode (Command: k m)
To lock the remote control and the front panel controls
on the set.
Transmission [k] [m] [] [Set !D] [] [Data] [Cr]
Data 0: Lock off Data 1: Lock on
Acknowledgement [m] [] [Set ID] [] [OK/NG] [Data] [x]
If you're not using the remote control and front panel
controls on the TV, use this mode. When main power is
on/off, remote control lock is released.
14. Treble (Command: k r)
To adjust treble.
You can also adjust treble in the Audio menu.
Transmission [k] [r] [ ] [Set ID][ ][Data] [Cr]
Data Min: 0 - Max: 64 (*transmit by Hexadecimal code)
*Refer to 'Real data mapping 1 ' as shown below.
Acknowledgement [r][] [Set ID] [ ] [OK/NG] [Data] [x]
15. Bass (Command: k s)
To adjust bass.
You can also adjust bass in the Audio menu.
Transmission [k] [s] [ ] [Set lD] [ ] [Data] [Cr]
Data Min: 0 _ Max: 64 (*transmit by Hexadecimal code)
*Refer to 'Real data mapping 1 ' as shown below.
Acknowledgement [s] [ ] [Set ID] [ ] [OK/NG] [Data] [x]
16. Balance (Command: k t)
To adjust balance.
You can also adjust balance in the Audio menu.
Transmission [k] [t][] [Set ID][] [Data] [Cr]
Data Min: 0 _ Max: 64 (*transmit by Hexadecimal code)
*Refer to 'Real data mapping 1 ' as shown.
Acknowledgement [t] [ ] [Set ID] [ ] [OK/NG] [Data] [x]
17. Color Temperature (Command: k u)
To adjust color temperature.
You can also adjust color temperature in the Picture menu.
Transmission [k] [u] [] [Set ID] [] [Data] [Cr]
Data 0: Medium 1: Cool 2: Warm 3: User
Acknowledgement [u] [] [Set ID] [] [OK/NG] [Data] [x]
18. Red Adjustment (Command: k v)
To adjust red in color temperature
Transmission [k] [v] [] [Set ID] [] [Data] [Cr]
Data Min: 0 _ Max: 28
*Refer to 'Real data mapping 2' as shown below.
Acknowledgement [v] [] [Set ID] [] [OK/NG] [Data] [x]
19. Green Adjustment (Command: k w)
To adjust green in color temperature.
Transmission [k] [w] [] [Set ID] [] [Data] [Cr]
Data Min: 0 _ Max: 28
*Refer to 'Real data mapping 2' as shown below.
Acknowledgement [w] [] [set ID] [] [OK/NG] [Data] [x]
20. Blue Adjustment (Command: k $)
To adjust blue in color temperature.
Transmission [k] [$][ ][Set ID][ ][Data] [Cr]
Data Min: 0 - Max: 28
*Refer to 'Real data mapping 2' as shown below.
Acknowledgement [$][ ][Set ID] [ ] [OK/NG] [Data] [x]
21
Low Power (Command: j q)
To control the low power function on/off.
Transmission [) ][q][ ][Set ID][] [Data] [Cr] .............
Data 0: Low Power off
1: Low Power on
Acknowledgemen[ [q][] [Set ID][] [OK/NG] [Data] [x]
22. Auto Configuration (Command: j u)
To adjust picture position and minimize image shaking
automatically. Auto configuration only works in RGB-PC
mode.
Transmission [j ] [u] [ ] [Set ID][] [Data] [Cr]
Data 1 : To set
Acknowledgement [u] [ ][Set ID] [ ] [OK/NG] [Data] [x]
*Real data mapping 1 *Real data mapping 2
0: Step 0 0:-20
! 1:-19
A: Step 10 (SET ID 10) 3 : -18
F: Step 15 (SET ID 15) 13:-1
10: Step 16 (SET ID 16) 14:0
15:+1
63: Step 99 (SET ID 99)
64: Step 100 27:+19
28:+20
75